Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 11.46 seconds
Igt-Version 
IGT-Version: 2.3-g4987fcaab (x86_64) (Linux: 6.19.0-CI_DRM_18010-g84d640df1ee7+ x86_64)
Out 
Using IGT_SRANDOM=1771593889 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff8881086e9820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x140b/0x1d70 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x407/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1243/0x26b0
     do_syscall_64+0x93/0x1470
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Subtest basic-rte: SUCCESS (11.460s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff8881086e9820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b79/0x26b0
     do_syscall_64+0x93/0x1470
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.460s)
Dmesg
<6> [93.810702] Console: switching to colour dummy device 80x25
<6> [93.810802] [IGT] kms_pm_rpm: executing
<6> [93.821985] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [93.822208] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [93.824829] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [93.825172] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [93.825358] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [93.825539] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [93.826221] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [93.826390] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [93.826398] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [93.826599] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [93.831574] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [93.831965] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [93.831971] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [93.832566] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [93.833177] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [93.833789] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [93.834468] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [93.834953] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [93.835536] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [93.835884] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [93.835890] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [93.836319] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [93.836495] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [93.836976] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [93.837282] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [93.837289] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [93.837493] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [93.841581] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [93.841586] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [93.841809] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [93.842074] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [93.842079] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [93.846306] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [93.846324] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [93.846328] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [93.847047] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [93.847540] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [93.848154] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [93.848170] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [93.848175] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [93.848597] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [93.848834] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [93.849250] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [93.849450] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [93.849454] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [93.849616] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [93.853895] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [93.853901] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [93.854089] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [93.854124] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [93.854130] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [93.858444] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [93.858485] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [93.858490] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [93.859256] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [93.859728] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [93.860453] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [93.860494] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [93.860499] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [93.860961] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [93.861133] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [93.861505] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [93.861707] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [93.861711] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [93.861911] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [93.866165] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [93.866170] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [93.866359] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [93.935942] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [93.936502] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [93.937030] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [93.937534] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [93.938459] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [104.915707] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [104.926014] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [104.950672] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [104.955632] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [104.956299] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [104.956271] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [104.960671] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [104.984712] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [104.990686] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [104.990972] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [104.991297] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.992011] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [104.992857] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [104.992763] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [104.997189] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [104.997687] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [104.998866] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [104.999773] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [105.001512] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [105.001456] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [105.002079] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.002378] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [105.002908] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.003248] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.003256] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [105.003546] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [105.007955] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.007959] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [105.010719] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [105.010922] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.011107] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [105.011287] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [105.011948] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [105.012170] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [105.015660] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [105.109341] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [105.121667] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [105.129238] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [105.129754] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [105.130375] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.131245] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [105.132649] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [105.132394] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [105.137133] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [105.138026] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [105.139671] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [105.140756] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [105.142618] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [105.143342] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.143793] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [105.144425] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.144979] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.144991] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [105.145411] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [105.150072] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.150084] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [105.150781] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [105.151303] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.151814] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [105.152301] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [105.153253] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [105.153761] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [105.154231] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.155023] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [105.156007] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [105.174735] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.175093] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [105.175422] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [105.176247] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [105.176638] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [105.180642] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [105.268752] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [105.277174] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [105.277705] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [105.278203] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [105.279091] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.279894] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [105.282169] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [105.282538] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [105.282885] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [105.283564] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [105.285018] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [105.286096] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [105.287809] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [105.287803] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [105.288428] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.288764] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [105.289291] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.289689] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.289698] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [105.289991] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [105.294346] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.294354] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [105.295013] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [105.383903] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [105.384730] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.385413] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [105.386070] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [105.387177] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [105.387859] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [105.394664] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [105.512771] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [105.524323] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [105.524978] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [105.525629] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.526645] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [105.528320] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [105.528349] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<6> [105.529237] [IGT] kms_pm_rpm: exiting, ret=0
<7> [105.533311] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [105.534076] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [105.535558] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [105.536654] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<6> [105.538943] Console: switching to colour frame buffer device 128x48
<7> [105.538801] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [105.539849] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.540707] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [105.541381] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.541884] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.541895] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [105.542313] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [105.545713] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [105.546235] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.546703] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [105.547078] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [105.547948] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.547957] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [105.548327] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [105.548951] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [105.549350] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.550182] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [105.568718] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.569012] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [105.569268] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [105.569996] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2026-02-20 16:14:33