Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 1.49 seconds
Igt-Version 
IGT-Version: 2.3-g4987fcaab (x86_64) (Linux: 6.19.0-CI_DRM_18009-g5cea68971b03+ x86_64)
Out 
Using IGT_SRANDOM=1771587360 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88810e379820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x140b/0x1d70 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x407/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1243/0x26b0
     do_syscall_64+0x93/0x1470
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.488s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.488s)
Dmesg
<6> [210.471646] Console: switching to colour dummy device 80x25
<6> [210.472319] [IGT] kms_pm_rpm: executing
<7> [210.475700] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [210.482178] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [210.482190] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [210.486483] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [210.486846] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [210.486852] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [210.487178] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [210.487491] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [210.487864] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [210.487870] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [210.488235] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [210.488521] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [210.488996] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1]
<7> [210.489003] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:389:eDP-1]
<7> [210.489616] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [210.490055] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [210.490258] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [210.490455] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [210.490685] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [210.490693] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [210.490697] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD monitor
<7> [210.490700] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD size 20, SAD count 0
<7> [210.490724] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] VRR capable: no
<7> [210.490918] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [210.491131] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [210.491958] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1] probed modes:
<7> [210.491965] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [210.491970] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [210.492000] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [210.492006] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [210.496308] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [210.496337] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [210.496342] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [210.496673] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [210.496690] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [210.496695] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [210.497003] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [210.497047] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1]
<7> [210.497053] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:389:eDP-1]
<7> [210.497640] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [210.498064] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [210.498255] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [210.498445] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [210.498668] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [210.498675] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [210.498679] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD monitor
<7> [210.498682] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD size 20, SAD count 0
<7> [210.498705] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] VRR capable: no
<7> [210.498905] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [210.499148] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [210.499965] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1] probed modes:
<7> [210.499972] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [210.499976] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [210.500054] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [210.500060] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [210.504355] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [210.504415] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [210.504420] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [210.504739] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [210.504803] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [210.504807] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [210.505135] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [210.505574] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:425]
<7> [211.540956] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [211.541419] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [211.542347] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [211.543108] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [211.543406] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [211.543617] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7843931/8388608 link 522928/524288, found tu 0, data 0/0 link 0/0)
<7> [211.543824] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [211.544049] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [211.544262] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3840, found 0)
<7> [211.544469] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 4000, found 0)
<7> [211.544676] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3840, found 0)
<7> [211.544882] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 4000, found 0)
<7> [211.545091] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3888, found 0)
<7> [211.545306] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3920, found 0)
<7> [211.545510] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 2160, found 0)
<7> [211.545713] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 2161, found 0)
<7> [211.545917] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 2163, found 0)
<7> [211.546118] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 2168, found 0)
<7> [211.546330] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 2244, found 0)
<7> [211.546535] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 2244, found 0)
<7> [211.546741] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3840, found 0)
<7> [211.546947] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 4000, found 0)
<7> [211.547147] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3840, found 0)
<7> [211.547358] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 4000, found 0)
<7> [211.547562] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3888, found 0)
<7> [211.547765] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3920, found 0)
<7> [211.547969] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 2160, found 0)
<7> [211.548197] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 2161, found 0)
<7> [211.548406] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 2163, found 0)
<7> [211.548609] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 2168, found 0)
<7> [211.548812] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 2244, found 0)
<7> [211.549027] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 2244, found 0)
<7> [211.549235] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [211.549445] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [211.549653] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [211.549859] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [211.550075] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 538600, found 0)
<7> [211.550292] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 538600, found 0)
<7> [211.550500] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [211.550706] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [211.550915] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [211.551136] i915 0000:00:02.0: [drm:intel_dpll_crtc_put [i915]] [CRTC:150:pipe A] releasing DPLL 0
<7> [211.551394] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [211.551595] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:150:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [211.551830] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [211.552071] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:144:cursor A] ddb (4027 - 4096) -> ( 0 - 0), size 69 -> 0
<7> [211.552280] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [211.552480] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [211.552673] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [211.552874] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [211.553108] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [211.553320] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [211.553522] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [211.553722] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [211.553922] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [211.554133] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [211.554345] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [211.554549] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [211.554766] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:150:pipe A] min cdclk: 269300 kHz -> 0 kHz
<7> [211.555033] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 33663 kHz -> 0 kHz
<7> [211.555186] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [211.555284] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [211.555435] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [211.555439] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [211.555492] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 179200 kHz, actual 179200 kHz
<7> [211.555678] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [211.555707] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [211.555928] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:150:pipe A] enable: no [modeset]
<7> [211.556157] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:34:plane 1A] fb: [NOFB], visible: no
<7> [211.556374] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [211.556578] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [211.556783] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [211.557012] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [211.557233] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [211.557542] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [211.558371] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [211.763188] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:389:eDP-1] set backlight PWM = 0
<7> [211.764165] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [211.776719] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turn panel power off
<7> [211.776963] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x00000089, pins 0x00000010, long 0x00000000
<7> [211.777516] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [211.777708] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:388:DDI A/PHY A] - short
<7> [211.778223] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [211.832741] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [211.833622] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:388:DDI A/PHY A] - long
<7> [211.834371] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [211.839065] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [211.839579] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A
<7> [211.840146] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:388:DDI A/PHY A]
<7> [211.840145] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:150:pipe A]
<7> [211.840651] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:388:DDI A/PHY A]
<7> [211.840728] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disabling DPLL 0
<7> [211.841269] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [211.841816] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [211.842454] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=448
<7> [211.842945] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:388:DDI A/PHY A]
<7> [211.843494] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:397:DDI B/PHY B]
<7> [211.843974] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:406:DDI TC1/PHY TC1]
<7> [211.844486] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:408:DP-MST A]
<7> [211.844957] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST B]
<7> [211.845437] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST C]
<7> [211.845892] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:415:DDI TC2/PHY TC2]
<7> [211.846364] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:417:DP-MST A]
<7> [211.846815] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST B]
<7> [211.847289] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST C]
<7> [211.847759] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:389:eDP-1]
<7> [211.848605] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 2 (mbus joined: no)
<7> [211.849093] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: yes -> no (pipe: *)
<7> [211.849537] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [211.850154] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_A
<7> [211.850763] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:150:pipe A]
<7> [211.851931] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [211.852362] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [211.870227] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [211.871114] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [211.871865] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [211.872890] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [211.874735] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [211.878945] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [211.880220] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [211.881267] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [211.882359] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [211.883157] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [211.883676] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [211.885283] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [211.958721] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [211.975292] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [211.987489] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [211.987698] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [211.987949] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [211.988232] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [211.988660] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [211.989686] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [211.990658] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [211.992126] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [211.992673] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [211.993011] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [211.995338] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [211.995552] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [211.999694] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [212.001289] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [212.001572] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.001793] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [212.002195] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [212.003000] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [212.003502] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [212.007347] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [212.007643] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [212.008063] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [212.008318] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [212.009167] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [212.009790] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [212.010386] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [212.011682] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [212.012115] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [212.012860] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [212.031352] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [212.031813] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [212.032216] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [213.027472] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [213.028537] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [213.029565] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [213.030498] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [213.031133] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [213.031689] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [213.032214] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [213.032976] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [213.032962] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [213.033476] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [213.034118] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [213.034641] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [213.035151] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [213.035654] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [213.036152] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [213.036956] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [213.038179] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [213.038176] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [213.039572] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [213.040890] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [213.041874] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [213.043166] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [213.043800] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [213.044325] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [213.044857] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [213.117842] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [213.118069] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:389:eDP-1]
<7> [213.118439] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:389:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [213.119453] i915 0000:00:02.0: [drm:intel_dp_compute_config_limits [i915]] [ENCODER:388:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 538600 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [213.120156] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp input 30 compressed 0.0000 HDR no link rate required 2019750 available 2160000
<7> [213.120757] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [213.121401] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:388:DDI A/PHY A] [CRTC:150:pipe A]
<7> [213.121913] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [213.122307] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [213.122530] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [213.122750] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [213.122986] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [213.123210] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [213.123420] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3840)
<7> [213.123626] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 4000)
<7> [213.123846] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3840)
<7> [213.124104] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 4000)
<7> [213.124332] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3888)
<7> [213.124554] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3920)
<7> [213.124770] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 2160)
<7> [213.124989] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 2161)
<7> [213.125208] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 2163)
<7> [213.125430] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 2168)
<7> [213.125659] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 2244)
<7> [213.125897] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 2244)
<7> [213.126150] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3840)
<7> [213.126392] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 4000)
<7> [213.126605] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3840)
<7> [213.126815] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 4000)
<7> [213.127056] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3888)
<7> [213.127288] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3920)
<7> [213.127510] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 2160)
<7> [213.127735] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 2161)
<7> [213.127955] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 2163)
<7> [213.128178] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 2168)
<7> [213.128403] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 2244)
<7> [213.128630] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 2244)
<7> [213.128864] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [213.129112] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [213.129349] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [213.129578] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [213.129784] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [213.130004] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [213.130238] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [213.130562] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [213.130777] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [213.131030] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [213.131233] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69
<7> [213.131421] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [213.131626] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [213.131840] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [213.132076] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [213.132339] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 2154400 num active planes 1
<7> [213.132565] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [213.132773] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [213.133000] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [213.133236] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [213.133458] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [213.133680] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [213.133898] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [213.134123] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 269300 kHz
<7> [213.134391] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 0 kHz -> 33663 kHz
<7> [213.134660] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [213.134895] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 307200 kHz, actual 307200 kHz
<7> [213.135141] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [213.135381] i915 0000:00:02.0: [drm:intel_find_dpll [i915]] [CRTC:150:pipe A] allocated DPLL 0
<7> [213.135597] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:150:pipe A] reserving DPLL 0
<7> [213.135814] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [213.136043] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [213.136277] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [213.136505] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [213.136732] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [213.136955] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0
<7> [213.137176] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [213.137404] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64
<7> [213.137638] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [213.137870] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: disabled
<7> [213.138113] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled
<7> [213.138346] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [213.138554] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum HBlank: 0
<7> [213.138757] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [213.138987] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] DP SDP: VSC, revision 4, length 14
<7> [213.139217] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pixelformat: RGB
<7> [213.139439] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] colorimetry: sRGB
<7> [213.139661] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bpc: 0
<7> [213.139897] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dynamic range: VESA range
<7> [213.140140] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] content type: Not defined
<7> [213.140371] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1
<7> [213.140591] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [213.140825] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: yes, vmin: 2244, vmax: 2244, flipline: 2244, pipeline full: 0, guardband: 82 vsync start: 81, vsync end: 76
<7> [213.141077] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 2162, vmax vblank: 2162, vmin vtotal: 2244, vmax vtotal: 2244
<7> [213.141316] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [213.141536] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [213.141748] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [213.141953] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [213.142196] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [213.142423] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [213.142640] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600, min cdclk 269300
<7> [213.142858] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0
<7> [213.143079] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [213.143301] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [213.143524] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [213.143757] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [213.144008] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [213.144250] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [213.144463] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [213.144666] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [213.144878] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [213.145117] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [213.145348] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [213.145566] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [213.145789] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [213.146015] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [213.146243] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [213.146455] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [213.146687] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [213.146929] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:34:plane 1A] fb: [FB:425] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [213.147184] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [213.147420] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0
<7> [213.147637] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [213.147840] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [213.148070] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [213.148297] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [213.148519] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [213.160065] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [213.160238] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [213.160425] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [213.160625] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [213.160871] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [213.161132] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [213.161447] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [213.161812] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [213.162119] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [213.162479] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [213.165207] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [213.165418] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [213.168570] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [213.169175] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [213.170760] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [213.172557] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [213.173003] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [213.173610] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [213.173870] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [213.174186] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=768
<7> [213.174572] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:388:DDI A/PHY A]
<7> [213.174871] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:397:DDI B/PHY B]
<7> [213.175159] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:406:DDI TC1/PHY TC1]
<7> [213.175402] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:408:DP-MST A]
<7> [213.175691] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST B]
<7> [213.175999] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST C]
<7> [213.176299] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:415:DDI TC2/PHY TC2]
<7> [213.176589] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:417:DP-MST A]
<7> [213.176819] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST B]
<7> [213.177027] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST C]
<7> [213.177444] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf
<7> [213.177795] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: no -> yes (pipe: *)
<7> [213.178070] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 4 (mbus joined: yes)
<7> [213.178377] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [213.178616] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [213.178827] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enabling DPLL 0
<7> [213.179241] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turn panel power on
<7> [213.179501] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [213.179795] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [213.190065] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [213.190392] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power on
<7> [213.190620] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [213.252784] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [213.253594] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:388:DDI A/PHY A] - long
<7> [213.254267] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [213.255047] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:388:DDI A/PHY A]
<7> [213.410072] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [213.411160] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A
<7> [213.412542] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turning VDD on
<7> [213.413452] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [213.416069] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80
<7> [213.416104] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [213.416642] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06
<7> [213.417532] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [213.417791] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [213.418763] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Clock recovery OK
<7> [213.419235] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [213.420981] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [213.421394] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [213.422314] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [213.423127] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [213.423549] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [213.424043] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:389:eDP-1] Performing OUI wait (0 ms)
<7> [213.424882] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:389:eDP-1] set backlight PWM = 6844
<7> [213.440031] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [213.443251] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:389:eDP-1]
<7> [213.444297] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:150:pipe A]
<7> [213.446852] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<6> [213.448955] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [213.450660] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:425] from all active usage due to RMFB ioctl
<7> [213.451670] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [213.452534] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [213.453286] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [213.454107] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [213.454807] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:425] is removed
<7> [213.455031] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [213.455538] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [213.456026] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [213.456513] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [213.457020] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [213.457547] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [213.458073] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [213.458571] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [213.459111] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [213.459624] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [213.460141] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [213.460644] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [213.461146] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [213.461937] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [213.474760] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [213.475410] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [213.475930] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [213.476435] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [213.476945] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [213.477537] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 2154400 num active planes 1
<7> [213.478068] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [213.478540] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [213.479014] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [213.479480] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [213.479946] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [213.480646] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [213.481186] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [213.490063] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [213.492650] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [213.493896] [IGT] kms_pm_rpm: exiting, ret=0
<6> [213.507378] Console: switching to colour frame buffer device 240x67
Created at 2026-02-20 13:28:56