Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.32 seconds
Igt-Version 
IGT-Version: 2.3-gd3c67e0f1 (x86_64) (Linux: 6.19.0-CI_DRM_18007-gcc2c646d3920+ x86_64)
Out 
Using IGT_SRANDOM=1771517436 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88813025d820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x960 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x306/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.316s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.316s)
Dmesg
<6> [120.798101] Console: switching to colour dummy device 80x25
<6> [120.798204] [IGT] kms_pm_rpm: executing
<7> [120.801375] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [120.807510] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [120.807521] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [120.807829] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.808560] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [120.809202] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [120.809824] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [120.810449] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.810739] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [120.811561] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.813081] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.814565] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.816071] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.817672] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.819257] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.820920] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.822518] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.823971] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.824903] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.825635] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.826036] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.826623] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [120.827291] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [120.827301] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [120.831720] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [120.832314] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [120.832324] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [120.900096] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [120.904251] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.904270] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [120.904846] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [120.908617] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.908634] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [120.909340] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [120.910563] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [120.910584] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [120.912072] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.912850] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [120.914311] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.916266] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.918175] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.920219] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.922398] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.924637] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.926726] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.928788] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.930816] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.932090] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.933353] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.933961] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.935021] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [120.935096] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [120.935113] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [120.939954] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [120.940094] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [120.940115] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [121.008683] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [121.012287] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.012298] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [121.012627] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [121.015741] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.015751] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [121.016146] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [121.016223] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [121.016233] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [121.016945] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [121.017395] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [121.018307] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.019932] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.021578] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.023110] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.024999] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.026775] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.028486] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.030186] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.031892] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.032846] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [121.033660] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [121.034100] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [121.034769] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [121.034934] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [121.034948] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [121.039671] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [121.039777] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [121.039787] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [121.108090] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [121.111911] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.111926] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [121.112422] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [121.116037] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.116051] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [121.116539] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [121.121152] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [121.121736] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [121.122279] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [121.122873] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [121.123999] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.124849] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.132453] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.157162] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.169196] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.170820] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.171609] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [122.180318] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.205016] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.216709] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.219026] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.219883] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.220928] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.223289] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [122.223159] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [122.224081] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.225684] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.226294] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.227446] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.229094] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.230691] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.232278] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.234074] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.235796] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.237569] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.239219] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.240803] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.241062] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.241539] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.241925] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.242274] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.243203] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.243826] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.244456] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.245547] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.246588] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.247263] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.248434] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [122.252878] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [122.321006] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.324735] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.324748] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.325154] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.328539] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.328551] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.330316] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [122.353051] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.353730] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.354389] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.355167] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.356413] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.358767] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.365587] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [122.435128] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [122.487075] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [122.499024] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.505768] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.506087] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.506405] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.506983] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.508089] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [122.508651] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [122.508737] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.509756] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.510251] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.511270] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.512875] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.514529] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.516027] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.517749] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.519405] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.520978] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.522554] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.524065] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.525079] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.526165] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.526989] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.528280] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [122.532671] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [122.600598] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.604529] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.604543] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.605001] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.609042] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.609055] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.609908] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [122.633247] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.634092] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.634744] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.635374] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.636582] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.637317] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.645978] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.724103] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.741368] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.742195] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.743050] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [122.745258] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.746772] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.748035] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.750577] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.751995] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 1 ms
<6> [122.752594] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [122.754382] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.758083] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.760399] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.762693] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.764800] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.766856] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.768797] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.770633] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.772444] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.773439] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.774726] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.775587] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.777054] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [122.781716] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [122.849596] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.853264] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.853276] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.853607] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.856790] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.856800] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.857380] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.858040] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.858639] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.859233] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.860290] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.860938] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.861334] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.862080] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.862852] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [122.863152] [IGT] kms_pm_rpm: exiting, ret=0
<6> [122.865730] Console: switching to colour frame buffer device 128x48
<7> [122.884031] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.884476] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.884845] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.885698] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2026-02-19 21:00:04