Result:
integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0
| Detail | Value |
|---|---|
| Duration | 1.49 seconds |
| Igt-Version |
IGT-Version: 2.3-g100eb9cb5 (x86_64) (Linux: 6.19.0-CI_DRM_18006-gc81e41f7aca9+ x86_64) |
| Out |
Using IGT_SRANDOM=1771493104 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88810928d820 has 1/1 users at
track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
__intel_runtime_pm_get+0x60/0x130 [i915]
i915_display_rpm_get_raw+0x17/0x30 [i915]
intel_display_rpm_get_raw+0x20/0x30 [i915]
__intel_display_power_put_async+0x3a/0x1c0 [i915]
intel_atomic_commit_tail+0x140b/0x1d70 [i915]
intel_atomic_commit+0x2e8/0x330 [i915]
drm_atomic_commit+0xaf/0xf0
drm_atomic_helper_set_config+0x82/0xd0
drm_mode_setcrtc+0x407/0xa10
drm_ioctl_kernel+0xb3/0x120
drm_ioctl+0x2d4/0x5a0
__x64_sys_ioctl+0xa5/0x100
x64_sys_call+0x1243/0x26b0
do_syscall_64+0x93/0x1470
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.488s)
|
| Err |
Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (1.488s) |
| Dmesg |
<6> [218.030948] Console: switching to colour dummy device 80x25
<6> [218.031507] [IGT] kms_pm_rpm: executing
<7> [218.034907] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [218.041190] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [218.041203] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [218.045540] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [218.045910] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [218.045916] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [218.046216] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [218.046501] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [218.047100] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [218.047112] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [218.047727] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [218.048291] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [218.049095] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1]
<7> [218.049108] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:389:eDP-1]
<7> [218.050043] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [218.050710] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [218.051105] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [218.051547] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [218.052000] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [218.052014] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [218.052022] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD monitor
<7> [218.052028] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD size 20, SAD count 0
<7> [218.052071] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] VRR capable: no
<7> [218.052523] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [218.052839] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [218.054151] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1] probed modes:
<7> [218.054164] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [218.054174] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [218.054228] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [218.054273] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [218.058783] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [218.058813] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [218.058818] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [218.059151] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [218.059169] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [218.059174] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [218.059498] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [218.059531] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1]
<7> [218.059537] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:389:eDP-1]
<7> [218.060339] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [218.060974] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [218.061350] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [218.061634] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [218.062006] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [218.062017] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [218.062023] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD monitor
<7> [218.062029] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:389:eDP-1] ELD size 20, SAD count 0
<7> [218.062065] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] VRR capable: no
<7> [218.062411] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [218.062742] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:389:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [218.063843] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:eDP-1] probed modes:
<7> [218.063854] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [218.063862] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [218.063955] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1]
<7> [218.063963] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [218.068401] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:HDMI-A-1] disconnected
<7> [218.068459] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1]
<7> [218.068464] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [218.068787] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:DP-1] disconnected
<7> [218.068852] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2]
<7> [218.068857] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [218.069157] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:416:DP-2] disconnected
<7> [218.069657] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:425]
<7> [219.081424] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [219.082445] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [219.083411] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [219.083391] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [219.084451] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [219.085402] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [219.103770] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [219.104027] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [219.104652] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [219.105229] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [219.105730] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [219.106249] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7843931/8388608 link 522928/524288, found tu 0, data 0/0 link 0/0)
<7> [219.106749] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [219.107275] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [219.107792] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3840, found 0)
<7> [219.108319] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 4000, found 0)
<7> [219.108819] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3840, found 0)
<7> [219.109359] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 4000, found 0)
<7> [219.109855] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3888, found 0)
<7> [219.110386] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3920, found 0)
<7> [219.110899] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 2160, found 0)
<7> [219.111438] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 2161, found 0)
<7> [219.111937] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 2163, found 0)
<7> [219.112455] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 2168, found 0)
<7> [219.112960] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 2244, found 0)
<7> [219.113495] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 2244, found 0)
<7> [219.114002] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3840, found 0)
<7> [219.114507] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 4000, found 0)
<7> [219.115010] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3840, found 0)
<7> [219.115540] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 4000, found 0)
<7> [219.116048] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3888, found 0)
<7> [219.116558] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3920, found 0)
<7> [219.117057] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 2160, found 0)
<7> [219.117574] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 2161, found 0)
<7> [219.118065] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 2163, found 0)
<7> [219.118562] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 2168, found 0)
<7> [219.119056] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 2244, found 0)
<7> [219.119588] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 2244, found 0)
<7> [219.120103] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [219.120638] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [219.121131] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [219.121630] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [219.122126] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 538600, found 0)
<7> [219.122656] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 538600, found 0)
<7> [219.123159] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [219.123641] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [219.124125] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [219.124661] i915 0000:00:02.0: [drm:intel_dpll_crtc_put [i915]] [CRTC:150:pipe A] releasing DPLL 0
<7> [219.125309] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [219.125768] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:150:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [219.126208] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [219.126657] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:144:cursor A] ddb (4027 - 4096) -> ( 0 - 0), size 69 -> 0
<7> [219.127116] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [219.127606] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [219.128068] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [219.128550] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [219.129044] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [219.129527] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [219.130035] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [219.130563] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [219.131061] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [219.131459] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [219.131814] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [219.132339] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [219.132841] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:150:pipe A] min cdclk: 269300 kHz -> 0 kHz
<7> [219.133409] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 33663 kHz -> 0 kHz
<7> [219.133716] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [219.134223] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 179200 kHz, actual 179200 kHz
<7> [219.134722] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [219.135241] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:150:pipe A] enable: no [modeset]
<7> [219.135734] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:34:plane 1A] fb: [NOFB], visible: no
<7> [219.136023] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [219.136267] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [219.136727] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [219.137242] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [219.137735] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [219.138425] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [219.139730] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [219.345472] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:389:eDP-1] set backlight PWM = 0
<7> [219.346579] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [219.357631] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turn panel power off
<7> [219.358424] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [219.359118] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [219.413643] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [219.414510] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:388:DDI A/PHY A] - long
<7> [219.415254] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [219.416036] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:388:DDI A/PHY A]
<7> [219.419269] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [219.419817] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A
<7> [219.420386] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:150:pipe A]
<7> [219.420957] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disabling DPLL 0
<7> [219.421460] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [219.421968] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [219.422487] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=448
<7> [219.422916] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:388:DDI A/PHY A]
<7> [219.423390] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:397:DDI B/PHY B]
<7> [219.423812] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:406:DDI TC1/PHY TC1]
<7> [219.424258] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:408:DP-MST A]
<7> [219.424688] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST B]
<7> [219.425118] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST C]
<7> [219.425606] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:415:DDI TC2/PHY TC2]
<7> [219.426051] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:417:DP-MST A]
<7> [219.426506] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST B]
<7> [219.426959] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST C]
<7> [219.427401] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:389:eDP-1]
<7> [219.428184] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 2 (mbus joined: no)
<7> [219.428612] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: yes -> no (pipe: *)
<7> [219.429053] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [219.429663] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_A
<7> [219.430243] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:150:pipe A]
<7> [219.431288] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [219.431677] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [219.449350] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [219.450140] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [219.450928] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [219.452020] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [219.453779] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [219.457749] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [219.459014] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [219.460024] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [219.461176] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [219.461999] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [219.462537] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [219.464187] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [219.537787] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [219.554662] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [219.566718] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [219.566942] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [219.567183] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [219.567450] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [219.567982] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [219.568765] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [219.569446] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [219.570586] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [219.571114] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [219.571477] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [219.574087] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [219.574319] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [219.578081] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [219.579178] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [219.579464] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [219.579977] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [219.580441] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [219.581233] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<7> [219.581625] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [219.586172] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [219.586458] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [219.586793] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [219.586985] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [219.587639] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [219.588527] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [219.588996] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [219.589766] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C]
<7> [219.590127] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [219.590435] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [219.590669] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [219.590944] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [219.591673] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [220.617341] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [220.618387] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [220.619428] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [220.620354] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [220.621069] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [220.621704] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [220.622137] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [220.622672] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [220.622681] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [220.623193] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [220.623778] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [220.623976] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [220.624193] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [220.624417] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [220.624619] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [220.625146] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [220.625567] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [220.625555] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [220.626474] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [220.627687] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [220.628623] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [220.629633] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [220.630225] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [220.630670] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [220.631138] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [220.694621] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [220.694750] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:389:eDP-1]
<7> [220.695133] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:389:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [220.696017] i915 0000:00:02.0: [drm:intel_dp_compute_config_limits [i915]] [ENCODER:388:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 538600 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [220.696689] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp input 30 compressed 0.0000 HDR no link rate required 2019750 available 2160000
<7> [220.697322] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [220.697911] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:388:DDI A/PHY A] [CRTC:150:pipe A]
<7> [220.698428] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [220.698952] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [220.699362] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [220.699577] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [220.699787] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [220.700006] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [220.700249] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3840)
<7> [220.700469] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 4000)
<7> [220.700684] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3840)
<7> [220.700893] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 4000)
<7> [220.701108] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3888)
<7> [220.701324] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3920)
<7> [220.701544] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 2160)
<7> [220.701766] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 2161)
<7> [220.701988] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 2163)
<7> [220.702220] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 2168)
<7> [220.702441] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 2244)
<7> [220.702653] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 2244)
<7> [220.702859] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3840)
<7> [220.703087] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 4000)
<7> [220.703308] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3840)
<7> [220.703524] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 4000)
<7> [220.703742] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3888)
<7> [220.703952] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3920)
<7> [220.704170] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 2160)
<7> [220.704389] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 2161)
<7> [220.704609] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 2163)
<7> [220.704832] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 2168)
<7> [220.705062] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 2244)
<7> [220.705290] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 2244)
<7> [220.705511] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [220.705721] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [220.705941] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [220.706176] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [220.706399] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [220.706615] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:150:pipe A] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [220.706827] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [220.707115] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [220.707317] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [220.707554] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [220.707759] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69
<7> [220.707963] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [220.708178] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [220.708381] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [220.708576] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [220.708800] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 2154400 num active planes 1
<7> [220.709028] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [220.709263] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [220.709483] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [220.709691] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [220.709894] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [220.710115] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [220.710338] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [220.710556] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 269300 kHz
<7> [220.710801] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 0 kHz -> 33663 kHz
<7> [220.711048] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [220.711272] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 307200 kHz, actual 307200 kHz
<7> [220.711489] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [220.711712] i915 0000:00:02.0: [drm:intel_find_dpll [i915]] [CRTC:150:pipe A] allocated DPLL 0
<7> [220.711937] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:150:pipe A] reserving DPLL 0
<7> [220.712178] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [220.712399] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [220.712611] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [220.712816] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [220.713027] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [220.713261] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0
<7> [220.713482] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [220.713695] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64
<7> [220.713906] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [220.714121] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: disabled
<7> [220.714339] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled
<7> [220.714556] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [220.714778] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum HBlank: 0
<7> [220.715002] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [220.715227] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] DP SDP: VSC, revision 4, length 14
<7> [220.715450] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pixelformat: RGB
<7> [220.715659] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] colorimetry: sRGB
<7> [220.715883] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bpc: 0
<7> [220.716114] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dynamic range: VESA range
<7> [220.716335] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] content type: Not defined
<7> [220.716551] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1
<7> [220.716763] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [220.716968] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: yes, vmin: 2244, vmax: 2244, flipline: 2244, pipeline full: 0, guardband: 82 vsync start: 81, vsync end: 76
<7> [220.717189] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 2162, vmax vblank: 2162, vmin vtotal: 2244, vmax vtotal: 2244
<7> [220.717412] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [220.717632] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [220.717855] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [220.718086] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [220.718305] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [220.718516] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [220.718740] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600, min cdclk 269300
<7> [220.718963] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0
<7> [220.719197] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [220.719417] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [220.719621] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [220.719826] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [220.720040] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [220.720276] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [220.720501] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [220.720714] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [220.720922] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [220.721136] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [220.721352] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [220.721570] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [220.721793] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [220.722016] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [220.722252] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [220.722472] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [220.722678] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [220.722887] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:34:plane 1A] fb: [FB:425] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [220.723122] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [220.723348] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0
<7> [220.723561] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [220.723773] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [220.723976] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [220.724188] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [220.724406] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [220.736183] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [220.736352] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [220.736552] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [220.736763] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [220.737018] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [220.737286] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [220.737589] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [220.737939] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [220.738235] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [220.739249] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [220.741692] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [220.741904] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [220.745098] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [220.745671] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [220.746284] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [220.749554] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [220.749953] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [220.750608] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [220.751098] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [220.751526] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=768
<7> [220.751987] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:388:DDI A/PHY A]
<7> [220.752208] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:397:DDI B/PHY B]
<7> [220.752511] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:406:DDI TC1/PHY TC1]
<7> [220.752870] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:408:DP-MST A]
<7> [220.753249] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST B]
<7> [220.753541] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST C]
<7> [220.753778] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:415:DDI TC2/PHY TC2]
<7> [220.754023] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:417:DP-MST A]
<7> [220.754425] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST B]
<7> [220.754794] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST C]
<7> [220.755369] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf
<7> [220.755810] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: no -> yes (pipe: *)
<7> [220.756211] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 4 (mbus joined: yes)
<7> [220.756650] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [220.757062] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [220.757333] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enabling DPLL 0
<7> [220.757722] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turn panel power on
<7> [220.758137] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [220.758604] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [220.769100] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [220.769500] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 wait for panel power on
<7> [220.769826] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [220.831598] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [220.832387] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:388:DDI A/PHY A] - long
<7> [220.833048] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [220.833739] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:388:DDI A/PHY A]
<7> [220.988509] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [220.989537] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A
<7> [220.990811] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 turning VDD on
<7> [220.991683] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:388:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [220.994257] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80
<7> [220.994288] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [220.994825] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06
<7> [220.995710] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [220.995966] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [220.996879] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Clock recovery OK
<7> [220.997313] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [220.999666] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [221.000107] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:389:eDP-1][ENCODER:388:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [221.001042] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [221.001812] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [221.002262] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [221.002697] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:389:eDP-1] Performing OUI wait (0 ms)
<7> [221.003559] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:389:eDP-1] set backlight PWM = 6844
<7> [221.018872] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [221.021861] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:389:eDP-1]
<7> [221.022865] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:150:pipe A]
<7> [221.025255] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:398:HDMI-A-1]
<6> [221.027259] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [221.028806] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:425] from all active usage due to RMFB ioctl
<7> [221.029971] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:407:DP-1]
<7> [221.030743] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [221.031483] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:416:DP-2]
<7> [221.032478] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [221.034392] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:425] is removed
<7> [221.034510] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [221.034897] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [221.035371] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [221.035831] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [221.036345] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [221.036842] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [221.037342] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [221.037829] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [221.038348] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [221.038853] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [221.039402] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [221.039901] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [221.040399] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [221.041109] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [221.053372] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [221.053951] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [221.054512] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [221.055020] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [221.055548] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [221.056103] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:150:pipe A] data rate 2154400 num active planes 1
<7> [221.056602] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [221.057174] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [221.057648] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [221.058194] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [221.058704] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [221.059233] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [221.059725] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [221.068667] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [221.071898] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [221.073594] [IGT] kms_pm_rpm: exiting, ret=0
<6> [221.085907] Console: switching to colour frame buffer device 240x67
|