Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.17 seconds
Igt-Version 
IGT-Version: 2.3-g30ecfbf68 (x86_64) (Linux: 6.19.0-CI_DRM_18005-ge1032fc6a7b9+ x86_64)
Out 
Using IGT_SRANDOM=1771456751 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88813e719820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x960 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x306/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.172s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.172s)
Dmesg
<7> [79.305838] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [79.306107] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [79.306308] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [79.306505] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [79.307165] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [79.310535] Console: switching to colour dummy device 80x25
<6> [79.310599] [IGT] kms_pm_rpm: executing
<7> [79.319276] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [79.322874] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [79.322882] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [79.323076] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [79.327479] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [79.327861] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [79.327867] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [79.328455] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [79.328986] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [79.329500] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [79.330143] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [79.330616] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [79.331214] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [79.331531] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [79.331536] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [79.331998] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [79.332165] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [79.332543] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [79.332740] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [79.332827] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [79.333018] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [79.337350] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [79.337355] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [79.337533] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [79.337786] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [79.337792] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [79.342054] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [79.342071] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [79.342075] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [79.342826] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [79.343303] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [79.343889] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [79.343905] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [79.343909] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [79.344382] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [79.344549] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [79.344982] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [79.345195] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [79.345199] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [79.345362] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [79.349646] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [79.349651] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [79.349867] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [79.349890] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [79.349895] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [79.354195] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [79.354278] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [79.354282] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [79.355016] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [79.355495] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [79.356094] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [79.356136] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [79.356140] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [79.356563] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [79.356728] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [79.357156] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [79.357382] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [79.357386] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [79.357550] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [79.361925] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [79.361929] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [79.362105] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [79.433996] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [79.434499] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [79.434990] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [79.435430] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [79.436346] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.538082] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [89.548332] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [90.426041] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [90.435605] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [90.436773] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.437043] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [90.438806] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [90.441890] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [90.442558] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [90.443181] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [90.443742] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [90.444909] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [90.445713] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [90.446933] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [90.447399] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.447570] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.447957] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.448162] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.448167] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.448335] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.452312] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.452317] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.452679] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [90.452810] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [90.554073] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [90.554496] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [90.554836] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [90.555197] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [90.556038] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.557140] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [90.561981] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [90.655132] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [90.674484] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [90.686025] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [90.693568] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [90.693980] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.694382] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [90.695103] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [90.696047] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [90.696499] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [90.700483] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [90.701002] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [90.702142] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [90.702931] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [90.704232] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [90.704482] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [90.705033] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.705209] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.705587] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.705790] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.705794] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.705997] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.710224] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.710230] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.713054] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [90.713259] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [90.713445] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [90.713626] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [90.714288] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.714555] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [90.718004] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [90.817099] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [90.824303] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [90.824813] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.825279] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [90.826282] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [90.826820] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [90.828297] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [90.830085] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [90.830843] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [90.832317] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [90.833260] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [90.834726] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [90.835196] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.835457] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.835839] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.836077] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.836085] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.836356] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.840648] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.840655] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.841211] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [90.841378] [IGT] kms_pm_rpm: exiting, ret=0
<6> [90.842711] Console: switching to colour frame buffer device 128x48
Created at 2026-02-19 01:16:08