Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.41 seconds
Igt-Version	IGT-Version: 2.3-gc45426aaf (x86_64) (Linux: 6.19.0-rc5-CI_DRM_17828-g7e8e6ec283f6+ x86_64)
Out	Using IGT_SRANDOM=1768542716 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88810e91d818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x13a1/0x1cb0 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x407/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1243/0x26b0 do_syscall_64+0x93/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.406s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88810e91d818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b79/0x26b0 do_syscall_64+0x93/0x1470
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.406s)
Dmesg	<6> [88.940581] Console: switching to colour dummy device 80x25 <6> [88.940631] [IGT] kms_pm_rpm: executing <6> [88.942431] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [88.942650] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [88.946808] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [88.946815] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [88.951041] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [88.951288] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [88.951292] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [88.955510] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [88.955750] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [88.955753] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [88.959963] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [88.960242] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [88.960245] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [88.964465] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [88.964477] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [88.964480] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [88.968674] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [88.968686] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [88.968689] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [88.972879] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [88.972897] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [88.972900] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [88.977086] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [88.977119] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [88.977122] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [88.981338] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [88.981369] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [88.981372] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [88.982374] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [88.982526] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [88.982667] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [88.986456] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [89.093525] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [89.988049] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [89.994099] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [89.995422] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [89.995653] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [89.995967] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [89.996106] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [89.997759] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [90.022931] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [90.029745] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [90.029992] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [90.030162] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [90.030387] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.030588] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.030796] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.031018] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.031192] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [90.031432] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [90.031563] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [90.031856] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [90.032558] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [90.033253] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [90.043652] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [90.044881] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [90.045096] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [90.045830] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [90.049812] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [90.054758] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [90.059554] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [90.059715] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [90.059857] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [90.060670] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [90.062109] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [90.062213] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [90.080808] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [90.081216] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [90.081580] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [90.083140] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [90.084190] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [90.087590] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [90.088952] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [90.089181] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [90.089462] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [90.089625] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [90.091716] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [90.163200] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [90.174852] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [90.182754] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [90.183583] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [90.184568] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [90.185598] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.186554] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.187560] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.188483] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.188749] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [90.189116] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [90.189248] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [90.189673] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [90.190352] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [90.190488] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [90.196629] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [90.196734] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [90.196890] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [90.197851] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [90.199263] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [90.199499] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [90.203566] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [90.203756] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [90.207976] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [90.226792] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [90.227147] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [90.227474] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [90.228993] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [90.229418] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [90.235182] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [90.236643] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [90.237457] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [90.238318] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [90.239055] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [90.243643] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [90.320787] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [90.328590] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [90.329413] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [90.330339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [90.331351] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.332310] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.333290] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.334190] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.335092] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [90.336236] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [90.336369] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [90.336717] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [90.337400] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [90.337552] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [90.346147] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [90.346310] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [90.346569] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <6> [90.348718] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [90.348894] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [90.351244] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [90.352282] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [90.353719] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [90.353881] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [90.358004] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [90.358170] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [90.452853] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [90.453774] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [90.454589] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [90.456585] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [90.457742] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [90.467353] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [90.468994] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [90.469992] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [90.470885] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [90.471434] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [90.476532] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [90.581100] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [90.589530] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [90.590346] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [90.591678] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [90.592643] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.593567] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.594483] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.595367] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [90.596306] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [90.597253] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [90.598095] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [90.599127] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [90.601715] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [90.602356] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [90.613880] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [90.614063] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [90.614241] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [90.615098] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [90.616520] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [90.616528] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <6> [90.616876] [IGT] kms_pm_rpm: exiting, ret=0 <7> [90.620947] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <6> [90.621173] Console: switching to colour frame buffer device 160x45 <7> [90.625327] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]

Created at 2026-01-16 08:03:16