Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.42 seconds
Igt-Version	IGT-Version: 2.3-gc45426aaf (x86_64) (Linux: 6.19.0-rc5-CI_DRM_17827-gef08aae71f50+ x86_64)
Out	Using IGT_SRANDOM=1768536170 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888118731818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x13a1/0x1cb0 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x407/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1243/0x26b0 do_syscall_64+0x93/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.417s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888118731818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b79/0x26b0 do_syscall_64+0x93/0x1470
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.417s)
Dmesg	<6> [66.712262] Console: switching to colour dummy device 80x25 <6> [66.712313] [IGT] kms_pm_rpm: executing <6> [66.714147] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [66.714353] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [66.718476] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [66.718483] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [66.722715] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [66.722988] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [66.722993] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [66.727188] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [66.727427] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [66.727430] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [66.731631] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [66.731957] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [66.731962] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [66.736232] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [66.736243] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [66.736246] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [66.740439] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [66.740451] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [66.740453] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [66.744643] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [66.744661] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [66.744663] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [66.747007] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [66.747246] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [66.747472] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [66.748872] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [66.748913] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [66.748916] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [66.753784] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [66.753814] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [66.753817] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [66.758667] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [66.859276] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.762067] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [67.768129] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [67.769510] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [67.769743] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [67.770023] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [67.770163] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [67.773623] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [67.798747] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [67.805609] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [67.805830] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [67.806000] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [67.806225] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.806427] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.806632] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.806830] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.807008] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [67.807248] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [67.807385] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [67.807642] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [67.808631] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [67.809321] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [67.818534] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [67.819755] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.820077] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [67.822194] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [67.824704] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [67.825781] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [67.827191] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [67.827413] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [67.831532] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [67.831706] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [67.854636] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [67.854803] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [67.854945] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [67.856215] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.856366] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [67.859955] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [67.861278] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [67.861610] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [67.862019] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [67.862253] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [67.864651] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [67.937057] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [67.948969] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [67.956811] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [67.957628] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [67.958548] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [67.959488] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.960418] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.961326] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.962232] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [67.963111] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [67.964789] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [67.965561] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [67.967001] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [67.969320] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [67.969830] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [67.978825] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [67.978998] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.979277] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [67.980109] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [67.981556] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [67.981747] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [67.985914] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [67.986013] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [67.990230] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [68.003931] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.004108] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.004243] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.005513] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.005666] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [68.009229] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.010565] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.010794] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.011093] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.011230] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.012861] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [68.099188] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [68.107018] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.107835] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.108732] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.109647] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.110566] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.111468] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.112353] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.113332] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.115029] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [68.115781] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.117239] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.119539] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.120079] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.129082] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [68.129244] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.129478] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <6> [68.131614] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [68.131794] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [68.134135] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.135174] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.136784] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [68.137012] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [68.141084] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [68.141251] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [68.237435] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.238334] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.239136] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.241125] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.242012] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [68.249268] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.250950] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.251905] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.252909] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.253709] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.260309] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [68.365890] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [68.374467] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.375288] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.376240] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.377209] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.378180] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.379129] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.380094] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.381017] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.382014] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [68.382898] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.383911] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.386540] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.387101] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.399795] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [68.399939] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.400123] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.401017] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.402630] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [68.402640] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <6> [68.403001] [IGT] kms_pm_rpm: exiting, ret=0 <7> [68.407103] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <6> [68.407340] Console: switching to colour frame buffer device 160x45 <7> [68.411500] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]

Created at 2026-01-16 06:37:28