Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.23 seconds
Igt-Version 
IGT-Version: 2.3-g7b26f6089 (x86_64) (Linux: 6.19.0-rc5-CI_DRM_17821-g733664f1edf3+ x86_64)
Out 
Using IGT_SRANDOM=1768412354 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff8881283b9818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x13a1/0x1cb0 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x407/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1243/0x26b0
     do_syscall_64+0x93/0x1470
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.225s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.225s)
Dmesg
<6> [82.956225] Console: switching to colour dummy device 80x25
<6> [82.956276] [IGT] kms_pm_rpm: executing
<7> [82.965495] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [82.969620] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1]
<7> [82.969626] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1]
<7> [82.973901] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected
<7> [82.974336] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1]
<7> [82.974341] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1]
<7> [82.978558] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected
<7> [82.978858] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2]
<7> [82.978863] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]
<7> [82.983097] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected
<7> [82.983399] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1]
<7> [82.983403] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1]
<7> [82.987609] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected
<7> [82.987622] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1]
<7> [82.987625] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1]
<7> [82.991845] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected
<7> [82.991858] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2]
<7> [82.991861] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]
<7> [82.996058] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected
<7> [82.996077] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1]
<7> [82.996080] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1]
<7> [83.000280] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected
<7> [83.000316] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1]
<7> [83.000319] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1]
<7> [83.002904] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [83.003083] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [83.003218] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [83.004580] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected
<7> [83.004618] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2]
<7> [83.004622] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]
<7> [83.009452] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected
<7> [83.115010] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [84.013573] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [84.018917] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [84.020242] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [84.020712] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [84.021000] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [84.021138] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [84.022986] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [84.049239] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [84.055831] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [84.055974] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [84.056148] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [84.056373] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.057077] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.057947] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.058818] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.059666] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [84.061461] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [84.062272] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [84.062848] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [84.063528] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [84.063663] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [84.072244] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [84.073570] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [84.073759] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [84.078375] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [84.079753] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [84.080192] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [84.080476] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [84.080614] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [84.082848] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [84.107292] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [84.115054] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [84.115917] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [84.116792] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [84.117707] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.118596] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.119507] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.120410] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.121281] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [84.122840] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [84.123516] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [84.124852] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [84.126732] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [84.127240] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [84.137349] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [84.137695] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [84.137845] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [84.138561] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [84.140169] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1]
<7> [84.140403] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B]
<7> [84.144726] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C]
<7> [84.144689] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1]
<7> [84.148931] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]
<7> [84.170841] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [84.171004] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [84.171141] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [84.172433] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [84.173270] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [84.178958] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [84.180436] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [84.181286] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [84.182106] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [84.182697] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [84.188509] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [84.254801] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [84.283883] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [84.295969] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [84.300713] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [84.301139] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [84.301702] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [84.302285] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.302880] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.303439] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.304018] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.304473] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [84.305509] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [84.305889] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [84.306368] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [84.307658] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [84.307935] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [84.316651] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [84.316763] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [84.316926] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [84.317873] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [84.319283] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1]
<7> [84.319519] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B]
<7> [84.323606] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1]
<7> [84.323777] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C]
<7> [84.327800] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]
<7> [84.349872] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [84.350282] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [84.350683] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [84.352207] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [84.352697] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [84.357289] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [84.358758] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [84.359578] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [84.360504] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [84.361216] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [84.367708] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [84.445230] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [84.453760] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [84.454576] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [84.455471] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [84.456406] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.457341] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.458234] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.459112] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [84.459965] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [84.461146] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [84.461941] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [84.462854] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [84.465250] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [84.466041] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [84.477772] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [84.477967] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [84.478168] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1]
<6> [84.480290] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [84.482781] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1]
<7> [84.487640] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]
<7> [84.492574] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [84.493605] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [84.495026] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [84.495138] [IGT] kms_pm_rpm: exiting, ret=0
<6> [84.496111] Console: switching to colour frame buffer device 160x45
Created at 2026-01-14 17:57:44