Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.43 seconds
Igt-Version	IGT-Version: 2.3-gf38f4d8e9 (x86_64) (Linux: 6.19.0-rc1-CI_DRM_17726-g34243f1cb0e3+ x86_64)
Out	Using IGT_SRANDOM=1766346605 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88810f395818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x136b/0x1c50 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x407/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1243/0x26b0 do_syscall_64+0x93/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.428s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88810f395818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b79/0x26b0 do_syscall_64+0x93/0x1470
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.428s)
Dmesg	<6> [70.847098] Console: switching to colour dummy device 80x25 <6> [70.847608] [IGT] kms_pm_rpm: executing <6> [70.849042] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [70.849251] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [70.853146] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [70.853153] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [70.857375] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [70.857634] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [70.857638] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [70.861875] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [70.862125] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [70.862128] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [70.866315] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [70.866585] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [70.866588] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [70.870769] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [70.870780] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [70.870783] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [70.874953] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [70.874968] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [70.874971] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [70.879183] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [70.879209] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [70.879212] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [70.883399] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [70.883458] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [70.883463] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [70.884202] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [70.884358] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.884495] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.888301] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [70.888356] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [70.888361] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [70.893181] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [70.996372] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [71.895816] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [71.900563] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.901969] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [71.902207] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [71.902498] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [71.902636] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [71.904491] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [71.929538] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [71.936425] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [71.936585] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [71.936753] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [71.936976] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.937175] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.937369] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.937594] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.937772] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [71.938507] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [71.939304] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [71.940350] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [71.942596] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.942904] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.950292] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [71.951648] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [71.951837] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [71.952645] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [71.956455] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [71.961350] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [71.966197] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [71.966329] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [71.966532] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [71.967313] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.968784] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [71.968971] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [71.986635] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [71.986992] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.987314] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.988805] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [71.989162] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [71.992533] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.993855] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [71.994088] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [71.994370] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [71.994504] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [71.996520] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [72.070105] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [72.082569] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [72.090416] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [72.091239] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [72.092210] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [72.093590] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.094970] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.096380] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.097684] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.098974] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [72.101412] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [72.102599] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [72.103969] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [72.106463] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [72.107174] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [72.116322] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [72.116500] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [72.116730] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [72.117519] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [72.118998] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [72.119188] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [72.123550] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [72.123717] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [72.127923] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [72.145442] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [72.145595] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [72.145728] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [72.147013] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [72.147445] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [72.151930] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [72.153349] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [72.153843] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [72.154419] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [72.154798] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [72.158276] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [72.240463] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [72.248371] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [72.249248] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [72.250506] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [72.251827] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.253246] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.254499] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.255790] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.257090] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [72.259429] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [72.260685] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [72.262717] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [72.265187] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [72.266009] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [72.275080] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [72.275178] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [72.275342] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <6> [72.278788] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [72.279017] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [72.280169] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [72.281133] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [72.282579] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [72.282888] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [72.286960] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [72.287126] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [72.379360] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [72.380259] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [72.381037] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [72.383055] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [72.384010] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [72.391379] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [72.393036] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [72.393879] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [72.394744] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [72.395394] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [72.400185] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [72.509592] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [72.516084] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [72.516231] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [72.516409] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [72.516635] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.516839] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.517736] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.519558] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.520889] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [72.522304] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [72.523524] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [72.524918] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [72.527747] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [72.528496] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [72.542494] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [72.542714] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [72.542955] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [72.543704] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [72.545371] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [72.545383] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <6> [72.545915] [IGT] kms_pm_rpm: exiting, ret=0 <7> [72.549871] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <6> [72.550186] Console: switching to colour frame buffer device 160x45 <7> [72.554271] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]

Created at 2025-12-23 11:01:36