Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 11.52 seconds
Igt-Version 
IGT-Version: 2.2-gf76e05461 (x86_64) (Linux: 6.18.0-CI_DRM_17621-g278f5507f31b+ x86_64)
Out 
Using IGT_SRANDOM=1764723946 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888113145818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x64/0x220 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x990 [i915]
     intel_dp_aux_transfer+0xd4/0x340 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x2e/0x70 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x2d8/0x7b0 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Subtest basic-rte: SUCCESS (11.518s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888113145818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x64/0x220 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b5e/0x26a0
     do_syscall_64+0x93/0xd60
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.518s)
Dmesg
<6> [92.833814] Console: switching to colour dummy device 80x25
<6> [92.833882] [IGT] kms_pm_rpm: executing
<6> [92.846723] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [92.846959] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [92.848248] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [92.848564] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [92.848849] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [92.849161] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [92.849956] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [92.850891] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [92.850899] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [92.851101] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [92.856164] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [92.856548] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [92.856553] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [92.857191] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [92.857711] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [92.858297] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [92.858986] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [92.859475] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [92.860070] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [92.860458] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [92.860464] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [92.860930] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.861115] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [92.861543] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.861765] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.861769] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [92.861952] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [92.866302] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.866307] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [92.866502] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [92.866752] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [92.866757] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [92.871033] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [92.871050] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [92.871053] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [92.871856] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [92.872339] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [92.872949] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [92.872965] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [92.872969] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [92.873510] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.873695] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [92.874091] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.874353] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.874357] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [92.874542] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [92.878705] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.878709] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [92.878905] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [92.878928] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [92.878932] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [92.883222] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [92.883264] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [92.883268] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [92.883995] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [92.884480] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [92.885075] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [92.885117] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [92.885122] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [92.885580] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.885764] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [92.886169] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.886407] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.886411] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [92.886595] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [92.890861] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.890865] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [92.891062] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [92.960302] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [92.960703] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [92.961052] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [92.961425] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [92.962330] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.940745] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.949115] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.973735] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.979109] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.979776] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.980166] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [103.980475] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [103.984802] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [103.986150] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.986843] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.987579] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.988963] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.989955] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.991413] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [103.991373] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [103.991842] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.992071] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.992519] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.992776] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.992780] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.992980] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.997199] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.997204] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.997558] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [104.096199] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [104.096717] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.097174] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [104.097588] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [104.098467] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [104.099005] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [104.104093] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [104.199437] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [104.211895] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [104.221727] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [104.222307] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [104.222983] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.223904] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [104.225122] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [104.225068] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [104.229841] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [104.230454] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [104.231736] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [104.232639] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [104.233873] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [104.234345] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [104.234546] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [104.234948] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [104.235199] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [104.235204] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [104.235401] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [104.239880] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [104.239884] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [104.240306] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [104.242151] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [104.242384] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.242588] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [104.242789] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [104.243482] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [104.243772] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [104.248107] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [104.352176] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [104.359627] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [104.360136] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [104.360664] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [104.361579] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.362518] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [104.364878] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [104.365339] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [104.366259] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [104.366261] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [104.367922] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [104.369010] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [104.370763] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [104.371467] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [104.371856] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [104.372507] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [104.372939] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [104.372947] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [104.373349] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [104.377658] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [104.377663] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [104.378115] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [104.378263] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [104.472301] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [104.473070] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.473752] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [104.474379] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [104.475503] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [104.476245] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [104.482102] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [104.595206] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [104.605966] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [104.606250] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [104.606524] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [104.607133] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [104.608048] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [104.608145] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<6> [104.608514] [IGT] kms_pm_rpm: exiting, ret=0
<7> [104.612443] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [104.612792] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [104.613786] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [104.614573] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<6> [104.616076] Console: switching to colour frame buffer device 128x48
<7> [104.615952] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [104.616566] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [104.616845] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [104.617268] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [104.617502] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [104.617507] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [104.617706] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [104.622008] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [104.622013] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [104.626123] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [104.626369] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [104.626646] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [104.626854] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [104.627550] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2025-12-04 23:04:33