Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 1.49 seconds
Igt-Version 
IGT-Version: 2.2-g3a460cb78 (x86_64) (Linux: 6.18.0-CI_DRM_17613-g4ee45005b554+ x86_64)
Out 
Using IGT_SRANDOM=1764603882 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88813c551818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x64/0x220 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x1349/0x1c40 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x407/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1144/0x26a0
     do_syscall_64+0x93/0xd60
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.493s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.493s)
Dmesg
<6> [254.660702] Console: switching to colour dummy device 80x25
<6> [254.661198] [IGT] kms_pm_rpm: executing
<7> [254.664041] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [254.670242] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:HDMI-A-1]
<7> [254.670259] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:217:HDMI-A-1]
<7> [254.674578] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:HDMI-A-1] disconnected
<7> [254.674992] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:DP-1]
<7> [254.674999] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:226:DP-1]
<7> [254.675337] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [254.675745] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:DP-1] disconnected
<7> [254.676536] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:235:DP-2]
<7> [254.676548] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:235:DP-2]
<7> [254.676986] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [254.677400] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:235:DP-2] disconnected
<7> [254.678337] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1]
<7> [254.678351] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:208:eDP-1]
<7> [254.679293] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [254.680007] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [254.680452] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [254.680855] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [254.681309] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [254.681324] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [254.681328] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD monitor
<7> [254.681331] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD size 20, SAD count 0
<7> [254.681351] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:208:eDP-1] VRR capable: no
<7> [254.681563] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:208:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [254.681933] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:208:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [254.683321] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] probed modes:
<7> [254.683333] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [254.683344] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [254.683394] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:HDMI-A-1]
<7> [254.683405] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:217:HDMI-A-1]
<7> [254.687925] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:HDMI-A-1] disconnected
<7> [254.687961] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:DP-1]
<7> [254.687968] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:226:DP-1]
<7> [254.688342] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:DP-1] disconnected
<7> [254.688363] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:235:DP-2]
<7> [254.688368] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:235:DP-2]
<7> [254.688880] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:235:DP-2] disconnected
<7> [254.688949] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1]
<7> [254.688959] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:208:eDP-1]
<7> [254.689910] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [254.690479] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [254.690836] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [254.691266] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [254.691729] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [254.691742] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [254.691750] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD monitor
<7> [254.691756] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD size 20, SAD count 0
<7> [254.691790] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:208:eDP-1] VRR capable: no
<7> [254.692164] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:208:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [254.692410] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:208:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [254.693572] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] probed modes:
<7> [254.693584] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [254.693594] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [254.693711] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:HDMI-A-1]
<7> [254.693721] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:217:HDMI-A-1]
<7> [254.698251] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:HDMI-A-1] disconnected
<7> [254.698312] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:DP-1]
<7> [254.698317] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:226:DP-1]
<7> [254.698639] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:DP-1] disconnected
<7> [254.698689] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:235:DP-2]
<7> [254.698693] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:235:DP-2]
<7> [254.698995] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:235:DP-2] disconnected
<7> [254.699419] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:244]
<7> [255.734534] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:89:pipe A]
<7> [255.734866] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [255.735723] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [255.736521] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [255.736608] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [255.736916] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [255.736972] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [255.736977] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [255.737134] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7843931/8388608 link 522928/524288, found tu 0, data 0/0 link 0/0)
<7> [255.737221] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [255.737361] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [255.737580] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [255.737786] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3840, found 0)
<7> [255.737992] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 4000, found 0)
<7> [255.738198] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3840, found 0)
<7> [255.738420] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 4000, found 0)
<7> [255.738631] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3888, found 0)
<7> [255.738836] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3920, found 0)
<7> [255.739041] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 2160, found 0)
<7> [255.739262] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 2161, found 0)
<7> [255.739475] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 2163, found 0)
<7> [255.739682] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 2168, found 0)
<7> [255.739887] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 2244, found 0)
<7> [255.740092] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 2244, found 0)
<7> [255.740307] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3840, found 0)
<7> [255.740519] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 4000, found 0)
<7> [255.740724] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3840, found 0)
<7> [255.740930] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 4000, found 0)
<7> [255.741134] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3888, found 0)
<7> [255.741348] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3920, found 0)
<7> [255.741559] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 2160, found 0)
<7> [255.741763] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 2161, found 0)
<7> [255.741968] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 2163, found 0)
<7> [255.742173] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 2168, found 0)
<7> [255.742397] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 2244, found 0)
<7> [255.742608] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 2244, found 0)
<7> [255.742813] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [255.743025] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [255.743248] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [255.743462] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [255.743671] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 538600, found 0)
<7> [255.743885] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 538600, found 0)
<7> [255.744090] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [255.744305] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [255.744523] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:89:pipe A] fastset requirement not met, forcing full modeset
<7> [255.744733] i915 0000:00:02.0: [drm:intel_dpll_crtc_put [i915]] [CRTC:89:pipe A] releasing DPLL 0
<7> [255.744999] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [255.745197] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:89:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [255.745454] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:33:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [255.745662] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:83:cursor A] ddb (4027 - 4096) -> ( 0 - 0), size 69 -> 0
<7> [255.745868] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [255.746064] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [255.746272] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [255.746475] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [255.746700] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:89:pipe A] data rate 0 num active planes 0
<7> [255.746911] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [255.747115] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [255.747332] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [255.747545] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [255.747748] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [255.747953] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [255.748158] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [255.748390] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:89:pipe A] min cdclk: 269300 kHz -> 0 kHz
<7> [255.748642] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 33663 kHz -> 0 kHz
<7> [255.748890] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [255.749107] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 179200 kHz, actual 179200 kHz
<7> [255.749330] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [255.749551] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:89:pipe A] enable: no [modeset]
<7> [255.749762] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:33:plane 1A] fb: [NOFB], visible: no
<7> [255.749982] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:43:plane 2A] fb: [NOFB], visible: no
<7> [255.750216] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:53:plane 3A] fb: [NOFB], visible: no
<7> [255.750437] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:63:plane 4A] fb: [NOFB], visible: no
<7> [255.750649] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:73:plane 5A] fb: [NOFB], visible: no
<7> [255.750853] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:83:cursor A] fb: [NOFB], visible: no
<7> [255.751144] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [255.752007] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [255.960495] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:208:eDP-1] set backlight PWM = 0
<7> [255.961514] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [255.970576] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:207:DDI A/PHY A] PPS 0 turn panel power off
<7> [255.971301] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [255.972007] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [256.026524] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [256.026693] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [256.027427] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:207:DDI A/PHY A] - long
<7> [256.027657] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A
<7> [256.028199] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [256.028580] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:89:pipe A]
<7> [256.029035] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:207:DDI A/PHY A]
<7> [256.029455] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disabling DPLL 0
<7> [256.030178] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [256.030918] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [256.031658] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=448
<7> [256.032093] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:207:DDI A/PHY A]
<7> [256.032322] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:216:DDI B/PHY B]
<7> [256.032529] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:225:DDI TC1/PHY TC1]
<7> [256.032737] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:227:DP-MST A]
<7> [256.032945] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:228:DP-MST B]
<7> [256.033153] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:229:DP-MST C]
<7> [256.033370] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:234:DDI TC2/PHY TC2]
<7> [256.033578] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:236:DP-MST A]
<7> [256.033774] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:237:DP-MST B]
<7> [256.033979] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DP-MST C]
<7> [256.034191] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:208:eDP-1]
<7> [256.034564] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 2 (mbus joined: no)
<7> [256.034777] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: yes -> no (pipe: *)
<7> [256.034978] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [256.035269] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_A
<7> [256.035538] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:89:pipe A]
<7> [256.036037] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:147:pipe B]
<7> [256.036234] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:205:pipe C]
<7> [256.054568] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [256.055367] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [256.055992] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [256.056950] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [256.059081] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [256.062903] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [256.064149] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [256.065098] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [256.066130] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [256.066965] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [256.067484] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [256.068269] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [256.140562] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [256.156778] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:89:pipe A]
<7> [256.168704] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [256.168883] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [256.169097] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [256.169344] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [256.169762] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [256.170618] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [256.171353] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [256.172649] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [256.172936] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [256.173315] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [256.175935] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [256.176153] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [256.180309] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [256.181326] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [256.181616] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [256.182000] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [256.182546] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [256.183253] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:217:HDMI-A-1]
<7> [256.183643] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:147:pipe B]
<7> [256.187966] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:226:DP-1]
<7> [256.188234] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [256.188705] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [256.189069] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [256.189886] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [256.190536] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:235:DP-2]
<7> [256.191164] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [256.191928] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [256.192416] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [256.193125] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:205:pipe C]
<7> [256.211552] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [256.212085] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [256.212609] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [257.208567] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [257.209689] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [257.210900] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [257.211911] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [257.212774] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [257.213515] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [257.213934] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [257.214468] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [257.214460] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [257.214973] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [257.215568] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [257.215775] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [257.215968] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [257.216160] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [257.216365] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [257.216895] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [257.217802] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [257.218033] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [257.218880] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [257.219541] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [257.220091] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [257.220592] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [257.220907] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [257.221113] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [257.221355] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [257.298069] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:89:pipe A]
<7> [257.298338] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:208:eDP-1]
<7> [257.298715] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:208:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [257.299784] i915 0000:00:02.0: [drm:intel_dp_compute_config_limits [i915]] [ENCODER:207:DDI A/PHY A][CRTC:89:pipe A] DP link limits: pixel clock 538600 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000
<7> [257.300559] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp input 30 compressed 0.0000 link rate required 2019750 available 2160000
<7> [257.301281] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:89:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [257.301941] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:207:DDI A/PHY A] [CRTC:89:pipe A]
<7> [257.302547] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [257.302802] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [257.303027] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [257.303263] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [257.303489] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [257.303708] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [257.303917] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3840)
<7> [257.304123] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 4000)
<7> [257.304359] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3840)
<7> [257.304593] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 4000)
<7> [257.304812] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3888)
<7> [257.305030] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3920)
<7> [257.305248] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 2160)
<7> [257.305471] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 2161)
<7> [257.305690] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 2163)
<7> [257.305922] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 2168)
<7> [257.306166] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 2244)
<7> [257.306418] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 2244)
<7> [257.306653] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3840)
<7> [257.306883] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 4000)
<7> [257.307099] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3840)
<7> [257.307328] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 4000)
<7> [257.307563] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3888)
<7> [257.307790] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3920)
<7> [257.308025] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 2160)
<7> [257.308268] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 2161)
<7> [257.308497] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 2163)
<7> [257.308711] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 2168)
<7> [257.308937] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 2244)
<7> [257.309170] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 2244)
<7> [257.309415] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [257.309643] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [257.309862] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [257.310070] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [257.310292] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [257.310524] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:89:pipe A] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [257.310752] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:89:pipe A] fastset requirement not met, forcing full modeset
<7> [257.311060] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [257.311290] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:89:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [257.311552] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [257.311750] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:83:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69
<7> [257.311955] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [257.312191] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [257.312409] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [257.312612] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [257.312850] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:89:pipe A] data rate 2154400 num active planes 1
<7> [257.313061] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [257.313281] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [257.313510] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [257.313738] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [257.313972] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [257.314215] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [257.314447] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [257.314658] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:89:pipe A] min cdclk: 0 kHz -> 269300 kHz
<7> [257.314903] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 0 kHz -> 33663 kHz
<7> [257.315163] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [257.315408] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 307200 kHz, actual 307200 kHz
<7> [257.315632] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [257.315857] i915 0000:00:02.0: [drm:intel_find_dpll [i915]] [CRTC:89:pipe A] allocated DPLL 0
<7> [257.316077] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:89:pipe A] reserving DPLL 0
<7> [257.316313] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:89:pipe A] enable: yes [modeset]
<7> [257.316541] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [257.316747] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [257.316948] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [257.317151] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [257.317370] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0
<7> [257.317588] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [257.317810] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64
<7> [257.318053] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [257.318317] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: disabled
<7> [257.318546] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled
<7> [257.318774] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [257.318978] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum HBlank: 0
<7> [257.319190] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [257.319421] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] DP SDP: VSC, revision 4, length 14
<7> [257.319649] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pixelformat: RGB
<7> [257.319881] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] colorimetry: sRGB
<7> [257.320117] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bpc: 0
<7> [257.320357] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dynamic range: VESA range
<7> [257.320589] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] content type: Not defined
<7> [257.320809] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1
<7> [257.321045] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [257.321291] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: yes, vmin: 2244, vmax: 2244, flipline: 2244, pipeline full: 0, guardband: 82 vsync start: 81, vsync end: 76
<7> [257.321522] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 2162, vmax vblank: 2162, vmin vtotal: 2244, vmax vtotal: 2244
<7> [257.321755] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [257.321982] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [257.322197] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [257.322427] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [257.322655] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [257.322894] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600, min cdclk 269300
<7> [257.323137] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0
<7> [257.323379] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [257.323607] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [257.323816] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [257.324044] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [257.324290] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [257.324520] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [257.324736] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [257.324942] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [257.325145] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [257.325365] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [257.325589] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [257.325814] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [257.326046] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [257.326291] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [257.326527] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [257.326737] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [257.326941] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [257.327169] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:33:plane 1A] fb: [FB:244] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [257.327417] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [257.327652] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0
<7> [257.327876] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:43:plane 2A] fb: [NOFB], visible: no
<7> [257.328092] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:53:plane 3A] fb: [NOFB], visible: no
<7> [257.328313] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:63:plane 4A] fb: [NOFB], visible: no
<7> [257.328534] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:73:plane 5A] fb: [NOFB], visible: no
<7> [257.328757] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:83:cursor A] fb: [NOFB], visible: no
<7> [257.341322] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [257.341487] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [257.341685] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [257.341897] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [257.342154] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [257.342415] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [257.342768] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [257.343264] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [257.343654] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [257.344908] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [257.348050] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [257.348273] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [257.351516] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [257.352103] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [257.353949] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [257.355344] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [257.355914] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [257.356556] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [257.356961] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [257.357594] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=768
<7> [257.358043] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:207:DDI A/PHY A]
<7> [257.358480] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:216:DDI B/PHY B]
<7> [257.358899] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:225:DDI TC1/PHY TC1]
<7> [257.359170] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:227:DP-MST A]
<7> [257.359384] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:228:DP-MST B]
<7> [257.359739] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:229:DP-MST C]
<7> [257.360207] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:234:DDI TC2/PHY TC2]
<7> [257.360656] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:236:DP-MST A]
<7> [257.361095] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:237:DP-MST B]
<7> [257.361522] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DP-MST C]
<7> [257.361964] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf
<7> [257.362550] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: no -> yes (pipe: *)
<7> [257.362998] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 4 (mbus joined: yes)
<7> [257.363514] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [257.363931] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:89:pipe A]
<7> [257.364143] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enabling DPLL 0
<7> [257.364666] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:207:DDI A/PHY A] PPS 0 turn panel power on
<7> [257.365104] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [257.365621] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [257.375278] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [257.375686] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power on
<7> [257.376020] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [257.438044] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [257.438940] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:207:DDI A/PHY A] - long
<7> [257.439687] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [257.440481] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:207:DDI A/PHY A]
<7> [257.595353] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [257.597336] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A
<7> [257.598509] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:207:DDI A/PHY A] PPS 0 turning VDD on
<7> [257.599245] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:207:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [257.601743] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80
<7> [257.601807] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [257.602714] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06
<7> [257.604131] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [257.604813] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [257.606110] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Clock recovery OK
<7> [257.606555] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [257.608216] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [257.608651] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [257.609612] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [257.610492] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [257.610931] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [257.611380] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:208:eDP-1] Performing OUI wait (0 ms)
<7> [257.612251] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:208:eDP-1] set backlight PWM = 6844
<7> [257.627338] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [257.630069] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:208:eDP-1]
<7> [257.630954] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:89:pipe A]
<7> [257.633192] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:217:HDMI-A-1]
<6> [257.635362] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [257.637157] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:244] from all active usage due to RMFB ioctl
<7> [257.637883] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:226:DP-1]
<7> [257.638733] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [257.639454] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:235:DP-2]
<7> [257.640201] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [257.642543] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:244] is removed
<7> [257.642691] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:33:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [257.643198] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [257.643682] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [257.644159] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [257.644655] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [257.645154] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:89:pipe A] data rate 0 num active planes 0
<7> [257.645645] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [257.646105] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [257.646635] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [257.647148] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [257.647669] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [257.648183] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [257.648652] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [257.649334] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [257.661786] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [257.662395] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [257.662870] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [257.663350] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [257.663861] i915 0000:00:02.0: [drm:skl_print_plane_changes [i915]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [257.664514] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:89:pipe A] data rate 2154400 num active planes 1
<7> [257.665009] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [257.665493] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [257.665978] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [257.666442] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [257.666958] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [257.667510] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [257.668007] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [257.677310] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [257.679460] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [257.680678] [IGT] kms_pm_rpm: exiting, ret=0
<6> [257.694723] Console: switching to colour frame buffer device 240x67
Created at 2025-12-01 17:40:50