Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 11.42 seconds
Igt-Version 
IGT-Version: 2.2-g005281c52 (x86_64) (Linux: 6.18.0-CI_DRM_17612-g7f7b6cfa09ab+ x86_64)
Out 
Using IGT_SRANDOM=1764584490 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811285d818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x64/0x220 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x1349/0x1c40 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x407/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1144/0x26a0
     do_syscall_64+0x93/0xd60
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Subtest basic-rte: SUCCESS (11.417s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811285d818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x64/0x220 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b5e/0x26a0
     do_syscall_64+0x93/0xd60
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.417s)
Dmesg
<6> [90.273211] Console: switching to colour dummy device 80x25
<6> [90.273281] [IGT] kms_pm_rpm: executing
<6> [90.283542] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [90.283775] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [90.287732] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [90.287740] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.288228] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [90.288489] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [90.288705] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [90.288918] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [90.292436] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [90.292776] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [90.292781] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [90.293888] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [90.294423] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [90.294959] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [90.295680] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [90.296162] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [90.296749] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [90.297084] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [90.297089] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [90.297540] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.297731] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.298153] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.298391] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.298395] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.298583] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.302716] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.302721] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.302919] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [90.303241] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [90.303246] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.307524] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [90.307541] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [90.307545] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [90.308302] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [90.308792] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [90.309437] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [90.309455] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [90.309459] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [90.309894] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.310157] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.310558] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.310781] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.310785] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.310968] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.315288] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.315293] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.315491] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [90.315516] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [90.315520] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.319761] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [90.319803] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [90.319807] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [90.320556] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [90.321018] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [90.321626] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [90.321668] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [90.321672] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [90.322140] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.322357] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.322746] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.322967] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.322971] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.323217] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.327437] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.327441] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.327637] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [90.400320] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [90.400913] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [90.401613] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [90.402307] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [90.403448] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [101.377442] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [101.386037] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [101.410810] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [101.417519] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [101.418497] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [101.418308] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.418884] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [101.419718] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [101.420764] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [101.420663] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [101.425364] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [101.425975] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [101.426994] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [101.427770] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [101.429001] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [101.429476] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.429660] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [101.430113] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.430364] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.430368] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.430553] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [101.434820] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.434824] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [101.435271] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [101.438094] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [101.438317] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [101.438522] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [101.438721] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [101.439385] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [101.439652] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [101.442849] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [101.536570] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [101.548128] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [101.557639] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [101.558180] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.558815] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [101.559712] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [101.560670] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [101.561011] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [101.565039] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [101.565345] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [101.566335] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [101.567241] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [101.568691] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [101.568685] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [101.569195] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.569477] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [101.569998] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.570345] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.570351] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.570608] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [101.575047] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.575053] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [101.578088] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [101.578312] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [101.578520] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [101.578719] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [101.579386] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [101.579654] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [101.582798] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [101.687139] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [101.696662] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [101.697239] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.697841] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [101.698117] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [101.699247] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [101.701396] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [101.702048] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [101.704561] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [101.705126] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [101.706353] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [101.707269] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [101.708722] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [101.708678] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [101.709185] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.709386] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [101.709782] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.710041] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.710046] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.710274] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [101.714636] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.714641] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [101.715052] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [101.808185] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [101.808722] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [101.809240] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [101.809700] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [101.810621] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [101.811175] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [101.815012] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [101.931111] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [101.941353] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [101.942024] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.942689] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [101.943810] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [101.944889] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [101.944887] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<6> [101.945395] [IGT] kms_pm_rpm: exiting, ret=0
<7> [101.949693] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [101.950049] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [101.951072] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [101.951841] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<6> [101.953246] Console: switching to colour frame buffer device 128x48
<7> [101.953185] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [101.953728] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.953990] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [101.954427] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.954663] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.954667] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.954851] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [101.959108] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.959112] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [101.963056] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [101.963293] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [101.963499] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [101.963740] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [101.964432] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2025-12-01 12:18:43