Results for igt@kms_pm_rpm@basic-rte

Result: Pass

integration-manifest git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 1.41 seconds
Igt-Version 
IGT-Version: 2.2-g069c5ee6e (x86_64) (Linux: 6.18.0-rc7-CI_DRM_17605-ge1c1b3e03e35+ x86_64)
Out 
Using IGT_SRANDOM=1764329004 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888116bad818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x64/0x220 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x1349/0x1c40 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x407/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1144/0x26a0
     do_syscall_64+0x93/0xd60
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Subtest basic-rte: SUCCESS (1.409s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888116bad818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x64/0x220 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b5e/0x26a0
     do_syscall_64+0x93/0xd60
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.409s)
Dmesg
<6> [70.975040] Console: switching to colour dummy device 80x25
<6> [70.975090] [IGT] kms_pm_rpm: executing
<6> [70.976945] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [70.977157] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [70.981115] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:HDMI-A-1]
<7> [70.981122] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:208:HDMI-A-1]
<7> [70.985342] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:HDMI-A-1] disconnected
<7> [70.985593] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:218:DP-1]
<7> [70.985597] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:218:DP-1]
<7> [70.989810] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:218:DP-1] disconnected
<7> [70.990052] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:HDMI-A-2]
<7> [70.990055] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:226:HDMI-A-2]
<7> [70.994252] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:HDMI-A-2] disconnected
<7> [70.994610] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:HDMI-A-1]
<7> [70.994614] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:208:HDMI-A-1]
<7> [70.998784] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:HDMI-A-1] disconnected
<7> [70.998797] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:218:DP-1]
<7> [70.998800] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:218:DP-1]
<7> [71.002978] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:218:DP-1] disconnected
<7> [71.002991] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:HDMI-A-2]
<7> [71.002994] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:226:HDMI-A-2]
<7> [71.007205] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:HDMI-A-2] disconnected
<7> [71.007223] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:HDMI-A-1]
<7> [71.007226] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:208:HDMI-A-1]
<7> [71.011465] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:HDMI-A-1] disconnected
<7> [71.011500] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:218:DP-1]
<7> [71.011502] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:218:DP-1]
<7> [71.015324] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [71.015483] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [71.015645] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [71.016933] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:218:DP-1] disconnected
<7> [71.017001] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:HDMI-A-2]
<7> [71.017007] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:226:HDMI-A-2]
<7> [71.021880] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:226:HDMI-A-2] disconnected
<7> [71.127119] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.020868] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.028197] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.029603] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.029841] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.030137] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.030276] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.032039] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.056049] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.062966] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.063189] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.063365] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.063591] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.063794] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.064019] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.064230] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.064407] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.064650] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [72.064783] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.065060] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.066531] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.067366] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.074108] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.075344] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.075491] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:89:pipe A]
<7> [72.075597] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.076543] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.078013] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:147:pipe B]
<7> [72.077973] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:208:HDMI-A-1]
<7> [72.082197] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:218:DP-1]
<7> [72.086405] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:226:HDMI-A-2]
<7> [72.090707] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:205:pipe C]
<7> [72.108974] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [72.109138] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.109278] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.110588] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.111398] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.118589] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.120316] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.121710] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.122592] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.123117] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.126800] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.191518] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:89:pipe A]
<7> [72.203774] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.211554] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.212392] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.213319] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.214268] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.215235] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.216147] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.217044] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.217917] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.219435] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [72.220296] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.221287] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.223757] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.224608] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.233866] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.234090] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.234387] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.235304] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.236767] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:208:HDMI-A-1]
<7> [72.237085] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:147:pipe B]
<7> [72.241020] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:218:DP-1]
<7> [72.245237] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:226:HDMI-A-2]
<7> [72.249590] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:205:pipe C]
<7> [72.267520] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [72.267674] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.267813] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.269084] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.269322] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.273992] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.275443] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.276111] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.276867] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.277305] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.280324] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.362295] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.370180] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.371021] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.371930] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.372868] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.373824] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.374741] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.375528] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.375707] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.376079] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [72.376217] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.376629] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.377317] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.377453] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.383585] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.383678] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.383815] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:208:HDMI-A-1]
<6> [72.386785] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [72.386947] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:89:pipe A]
<7> [72.388562] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:218:DP-1]
<7> [72.393460] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:226:HDMI-A-2]
<7> [72.398416] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.399460] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.400869] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:147:pipe B]
<7> [72.400978] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:205:pipe C]
<7> [72.490955] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [72.491862] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.492662] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.494697] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.496108] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.504956] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.506919] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.507933] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.508881] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.509484] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.513764] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.618878] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.626398] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.627234] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.628158] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.629129] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.630113] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.631037] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.631947] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [72.632849] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.633789] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [72.634600] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.635562] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.638044] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.638854] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.651829] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.652009] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.652252] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.653043] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.654638] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [72.654647] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:208:HDMI-A-1]
<6> [72.655007] [IGT] kms_pm_rpm: exiting, ret=0
<7> [72.658871] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:218:DP-1]
<7> [72.663302] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:226:HDMI-A-2]
<6> [72.663513] Console: switching to colour frame buffer device 160x45
Created at 2025-11-28 13:05:27