Result:
integration-manifest git-log-oneline i915_display_info3 igt_runner3 runtimes3 results3.json results3-i915-load.json i915_display_info_post_exec3 boot3 dmesg3
| Detail | Value |
|---|---|
| Duration | 7.36 seconds |
| Hostname |
shard-rkl-6 |
| Igt-Version |
IGT-Version: 2.2-g5af861520 (x86_64) (Linux: 6.18.0-rc5-CI_DRM_17545-ge15c082b1af0+ x86_64) |
| Out |
Using IGT_SRANDOM=1763126308 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888120c0d7f8 has 1/1 users at
track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
__intel_runtime_pm_get+0x64/0x220 [i915]
i915_display_rpm_get_raw+0x17/0x30 [i915]
intel_display_rpm_get_raw+0x1f/0x30 [i915]
__intel_display_power_put_async+0x3a/0x1c0 [i915]
intel_atomic_commit_tail+0x1349/0x1c40 [i915]
intel_atomic_commit+0x2e5/0x330 [i915]
drm_atomic_commit+0xaf/0xf0
drm_atomic_helper_set_config+0x82/0xd0
drm_mode_setcrtc+0x407/0xa10
drm_ioctl_kernel+0xb3/0x120
drm_ioctl+0x2d4/0x5a0
__x64_sys_ioctl+0xa5/0x100
x64_sys_call+0x1144/0x26a0
do_syscall_64+0x93/0xc80
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: system-suspend-execbuf
[cmd] rtcwake: assuming RTC uses UTC ...
[cmd] rtcwake: wakeup from "mem" using /dev/rtc0 at Fri Nov 14 13:18:46 2025
Subtest system-suspend-execbuf: SUCCESS (7.362s)
|
| Err |
Starting subtest: system-suspend-execbuf Subtest system-suspend-execbuf: SUCCESS (7.362s) |
| Dmesg |
<6> [118.220618] [IGT] i915_pm_rpm: executing
<7> [118.228409] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [118.235418] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [118.236061] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:148:HDMI-A-1]
<7> [118.236071] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [118.236330] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [118.240921] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:148:HDMI-A-1] disconnected
<7> [118.240966] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:158:HDMI-A-2]
<7> [118.240969] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [118.245795] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:158:HDMI-A-2] disconnected
<7> [118.245829] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:162:DP-1]
<7> [118.245832] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [118.250672] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:162:DP-1] disconnected
<7> [118.250704] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:169:HDMI-A-3]
<7> [118.250707] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [118.255534] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:169:HDMI-A-3] disconnected
<7> [118.258367] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:148:HDMI-A-1]
<7> [118.258372] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [118.262854] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:148:HDMI-A-1] disconnected
<7> [118.263121] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:158:HDMI-A-2]
<7> [118.263124] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [118.268903] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:158:HDMI-A-2] disconnected
<7> [118.269205] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:162:DP-1]
<7> [118.269209] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [118.274988] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:162:DP-1] disconnected
<7> [118.275303] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:169:HDMI-A-3]
<7> [118.275307] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [118.281116] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:169:HDMI-A-3] disconnected
<7> [118.281408] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:148:HDMI-A-1]
<7> [118.281411] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [118.286032] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:148:HDMI-A-1] disconnected
<7> [118.286045] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:158:HDMI-A-2]
<7> [118.286047] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [118.290905] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:158:HDMI-A-2] disconnected
<7> [118.290917] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:162:DP-1]
<7> [118.290920] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [118.296929] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:162:DP-1] disconnected
<7> [118.296941] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:169:HDMI-A-3]
<7> [118.296943] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [118.301881] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:169:HDMI-A-3] disconnected
<7> [118.403425] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.303500] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [119.310673] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.312056] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [119.312620] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [119.312905] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [119.313044] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [119.313280] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [119.338322] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [119.338721] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [119.339422] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [119.340108] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [119.340884] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.341651] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.342391] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.343097] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.343822] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [119.345191] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [119.345328] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [119.345580] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [119.346284] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.346430] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.353820] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [119.355049] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.355295] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [119.355642] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:88:pipe A]
<7> [119.361143] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [119.366143] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [119.370958] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [119.375820] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.375962] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.376114] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.376942] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.378410] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:145:pipe B]
<7> [119.396299] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.396609] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.396874] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.398367] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.398834] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [119.404511] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.405914] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [119.406218] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [119.406499] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [119.406639] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [119.406810] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [119.479782] [IGT] i915_pm_rpm: starting subtest system-suspend-execbuf
<7> [119.481495] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:88:pipe A]
<7> [119.493265] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [119.493666] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [119.494387] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [119.495200] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [119.496001] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.496815] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.497686] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.498451] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.499235] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [119.500673] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [119.501430] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [119.502753] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [119.505103] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.505804] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.516162] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [119.516331] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.516620] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.517374] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.518938] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [119.519139] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:145:pipe B]
<7> [119.523303] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [119.527509] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [119.531730] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [119.541418] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.541598] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.541745] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.543068] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.543306] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [119.546769] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.548140] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [119.548377] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [119.548660] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [119.548800] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [119.548971] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [119.730761] PM: suspend entry (s2idle)
<6> [119.748978] Filesystems sync: 0.018 seconds
<6> [119.768445] Freezing user space processes
<6> [119.778927] Freezing user space processes completed (elapsed 0.010 seconds)
<6> [119.779031] OOM killer disabled.
<6> [119.779038] Freezing remaining freezable tasks
<6> [119.780444] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
<7> [119.889469] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [119.890316] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [119.891055] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [119.891866] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [119.892704] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.893547] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.894355] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.895134] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [119.895973] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [119.897050] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [119.897775] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [119.900499] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [119.902791] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.903292] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.913401] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [119.913521] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.913689] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [119.918345] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [119.923216] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [119.925814] GFP mask restricted
<7> [119.928112] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<6> [119.934012] e1000e: EEE TX LPI TIMER: 00000011
<6> [119.934017] e1000e: EEE TX LPI TIMER: 00000000
<7> [119.934047] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.954598] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.954778] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.955643] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.957065] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [119.957414] i915 0000:00:02.0: [drm:intel_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [119.961818] azx_init_pci: snd_hda_intel 0000:00:1f.3: Clearing TCSEL
<7> [119.961849] azx_init_pci: snd_hda_intel 0000:00:1f.3: SCH snoop: Enabled
<7> [119.969205] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [119.969411] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.969580] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.969720] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.971018] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.972279] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.972455] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.973255] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.974689] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [119.974922] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [119.975151] i915 0000:00:02.0: [drm:drm_client_dev_suspend] fbdev: ret=0
<7> [119.976786] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind
<3> [119.993738] igc 0000:02:00.0 enp2s0: Timeout reading IGC_PTM_STAT register
<7> [120.359407] PM: suspend of devices complete after 433.575 msecs
<7> [120.359411] PM: start suspend of devices complete after 578.532 msecs
<7> [120.374480] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4
<7> [120.374727] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [120.374876] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [120.375024] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [120.375170] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [120.376508] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.377740] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [120.379117] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [120.379601] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [120.379909] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [120.380105] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [120.380492] PM: late suspend of devices complete after 21.078 msecs
<6> [120.391726] ACPI: EC: interrupt blocked
<7> [120.613060] PM: noirq suspend of devices complete after 231.505 msecs
<6> [120.613089] ACPI: \_SB_.PR00: LPI: Device not power manageable
<6> [120.613101] ACPI: \_SB_.PR01: LPI: Device not power manageable
<6> [120.613106] ACPI: \_SB_.PR02: LPI: Device not power manageable
<6> [120.613112] ACPI: \_SB_.PR03: LPI: Device not power manageable
<6> [120.613117] ACPI: \_SB_.PR04: LPI: Device not power manageable
<6> [120.613123] ACPI: \_SB_.PR05: LPI: Device not power manageable
<6> [120.613128] ACPI: \_SB_.PR06: LPI: Device not power manageable
<6> [120.613134] ACPI: \_SB_.PR07: LPI: Device not power manageable
<6> [120.613139] ACPI: \_SB_.PC00.GFX0: LPI: Device not power manageable
<6> [120.613150] ACPI: \_SB_.PR08: LPI: Device not power manageable
<6> [120.613156] ACPI: \_SB_.PR09: LPI: Device not power manageable
<6> [120.613170] ACPI: \_SB_.PR10: LPI: Device not power manageable
<6> [120.613192] ACPI: \_SB_.PR11: LPI: Device not power manageable
<6> [120.613198] ACPI: \_SB_.PC00.HECI: LPI: Device not power manageable
<6> [120.613217] ACPI: \_SB_.PC00.GNA0: LPI: Device not power manageable
<6> [120.616386] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off
<7> [120.689465] PM: Triggering wakeup from IRQ 9
<6> [120.756772] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry
<7> [120.756780] PM: suspend-to-idle
<7> [120.756927] ACPI: EC: ACPI EC GPE status set
<7> [120.756957] ACPI: PM: Rearming ACPI SCI for wakeup
<7> [135.565732] Timekeeping suspended for 14.827 seconds
<7> [135.565827] PM: Triggering wakeup from IRQ 9
<7> [135.567003] ACPI: PM: ACPI fixed event wakeup
<7> [135.567017] PM: resume from suspend-to-idle
<6> [135.718601] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit
<6> [135.721582] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on
<6> [135.722610] ACPI: EC: interrupt unblocked
<7> [136.091614] PM: noirq resume of devices complete after 370.014 msecs
<7> [136.101164] i915 0000:00:02.0: [drm:gen9_sanitize_dc_state [i915]] Resetting DC state tracking from 08 to 08
<7> [136.101985] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [136.102731] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [136.103588] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [136.104357] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [136.105133] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [136.105684] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [136.105948] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [136.106172] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [136.106702] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [136.106938] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [136.107360] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [136.108097] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [136.108241] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [136.108384] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [136.108685] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [136.108850] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [136.109148] PM: early resume of devices complete after 9.258 msecs
<7> [136.116299] i915 0000:00:02.0: [drm:intel_cdclk_read_hw [i915]] Current CDCLK 180000 kHz, VCO 720000 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [136.116546] i915 0000:00:02.0: [drm:nop_init_clock_gating [i915]] No clock gating settings or workarounds applied.
<7> [136.117391] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:88:pipe A] hw state readout: disabled
<7> [136.117636] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:145:pipe B] hw state readout: disabled
<7> [136.117800] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:33:plane 1A] hw state readout: disabled, pipe A
<7> [136.117985] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:43:plane 2A] hw state readout: disabled, pipe A
<7> [136.118146] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:53:plane 3A] hw state readout: disabled, pipe A
<7> [136.118312] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:63:plane 4A] hw state readout: disabled, pipe A
<7> [136.118472] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 5A] hw state readout: disabled, pipe A
<7> [136.118632] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:83:cursor A] hw state readout: disabled, pipe A
<7> [136.118796] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:90:plane 1B] hw state readout: disabled, pipe B
<7> [136.118994] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 2B] hw state readout: disabled, pipe B
<7> [136.119145] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:110:plane 3B] hw state readout: disabled, pipe B
<7> [136.119294] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:120:plane 4B] hw state readout: disabled, pipe B
<7> [136.119442] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:130:plane 5B] hw state readout: disabled, pipe B
<7> [136.119623] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:140:cursor B] hw state readout: disabled, pipe B
<7> [136.119832] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:147:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [136.120043] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:157:DDI TC1/PHY C] hw state readout: disabled, pipe A
<7> [136.120293] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:161:DDI TC2/PHY D] hw state readout: disabled, pipe A
<7> [136.120541] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:163:DP-MST A] hw state readout: disabled, pipe A
<7> [136.120798] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:164:DP-MST B] hw state readout: disabled, pipe B
<7> [136.121093] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [136.121383] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [136.121667] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [136.122137] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:148:HDMI-A-1] hw state readout: disabled
<7> [136.122461] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:158:HDMI-A-2] hw state readout: disabled
<7> [136.122760] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:162:DP-1] hw state readout: disabled
<7> [136.123035] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:169:HDMI-A-3] hw state readout: disabled
<6> [136.123212] nvme nvme0: D3 entry latency set to 10 seconds
<7> [136.123235] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:33:plane 1A] min_cdclk 0 kHz
<7> [136.123435] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:43:plane 2A] min_cdclk 0 kHz
<7> [136.123636] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:53:plane 3A] min_cdclk 0 kHz
<7> [136.123854] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:63:plane 4A] min_cdclk 0 kHz
<7> [136.124058] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 5A] min_cdclk 0 kHz
<7> [136.124264] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:83:cursor A] min_cdclk 0 kHz
<7> [136.124460] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:88:pipe A] min_cdclk 0 kHz
<7> [136.124663] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:90:plane 1B] min_cdclk 0 kHz
<7> [136.124876] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 2B] min_cdclk 0 kHz
<7> [136.125070] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:110:plane 3B] min_cdclk 0 kHz
<7> [136.125282] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:120:plane 4B] min_cdclk 0 kHz
<7> [136.125484] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:130:plane 5B] min_cdclk 0 kHz
<7> [136.125693] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:140:cursor B] min_cdclk 0 kHz
<7> [136.125991] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:145:pipe B] min_cdclk 0 kHz
<7> [136.126195] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:88:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [136.126386] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:145:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [136.126561] i915 0000:00:02.0: [drm:intel_bw_update_hw_state [i915]] pipe A data rate 0 num active planes 0
<7> [136.126752] i915 0000:00:02.0: [drm:intel_bw_update_hw_state [i915]] pipe B data rate 0 num active planes 0
<7> [136.127047] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:88:pipe A] enable: no [setup_hw_state]
<7> [136.127248] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:145:pipe B] enable: no [setup_hw_state]
<7> [136.127665] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 16761 required 0
<7> [136.127904] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:88:pipe A] enable: no [fastset]
<7> [136.128160] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:33:plane 1A] fb: [NOFB], visible: no
<7> [136.128352] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:43:plane 2A] fb: [NOFB], visible: no
<6> [136.128605] nvme nvme0: 12/0/0 default/read/poll queues
<7> [136.128551] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:53:plane 3A] fb: [NOFB], visible: no
<7> [136.128740] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:63:plane 4A] fb: [NOFB], visible: no
<7> [136.128983] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:73:plane 5A] fb: [NOFB], visible: no
<7> [136.129172] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:83:cursor A] fb: [NOFB], visible: no
<7> [136.129365] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:145:pipe B] enable: no [fastset]
<7> [136.129541] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:90:plane 1B] fb: [NOFB], visible: no
<7> [136.129716] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:100:plane 2B] fb: [NOFB], visible: no
<7> [136.129939] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:110:plane 3B] fb: [NOFB], visible: no
<7> [136.130121] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:120:plane 4B] fb: [NOFB], visible: no
<7> [136.130309] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:130:plane 5B] fb: [NOFB], visible: no
<7> [136.130477] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:140:cursor B] fb: [NOFB], visible: no
<7> [136.130685] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:88:pipe A]
<7> [136.130988] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:145:pipe B]
<7> [136.131924] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected
<7> [136.132180] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [136.136406] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [136.140282] i915 0000:00:02.0: [drm:drm_client_dev_resume] fbdev: ret=0
<7> [136.140298] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4
<7> [136.140644] i915 0000:00:02.0: [drm:intel_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [136.140742] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<6> [136.141648] serial 00:02: activated
<7> [136.145019] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [136.145434] azx_init_pci: snd_hda_intel 0000:00:1f.3: Clearing TCSEL
<7> [136.145444] azx_init_pci: snd_hda_intel 0000:00:1f.3: SCH snoop: Enabled
<7> [136.218996] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [136.219231] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [136.219382] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [136.219524] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [136.220830] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<3> [136.370853] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0
<6> [136.426706] ata4: SATA link down (SStatus 4 SControl 300)
<6> [136.426733] ata2: SATA link down (SStatus 4 SControl 300)
<6> [136.426760] ata3: SATA link down (SStatus 4 SControl 300)
<7> [136.851098] PM: resume of devices complete after 741.923 msecs
<7> [136.851763] GFP mask restored
<6> [136.855352] OOM killer enabled.
<6> [136.855357] Restarting tasks: Starting
<7> [136.856862] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind
<6> [136.857673] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
<6> [136.860111] Restarting tasks: Done
<7> [136.860205] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<5> [136.860965] random: crng reseeded on system resumption
<6> [136.861278] PM: suspend exit
<6> [136.861316] mei_pxp 0000:00:16.0-fbf6fcf1-96cf-4e2e-a6a6-1bab8cbe36b1: bound 0000:00:02.0 (ops i915_pxp_tee_component_ops [i915])
<7> [136.868636] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [136.870050] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [136.870762] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [136.871247] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [136.871393] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [136.871571] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [136.976925] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [136.977115] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [136.977331] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [136.977580] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [136.977897] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [136.978173] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [136.978458] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [136.978738] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [136.979039] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [136.979941] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [136.980123] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [136.980736] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [136.981542] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [136.981750] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<3> [136.986895] atkbd serio0: Failed to enable keyboard on isa0060/serio0
<7> [136.991944] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [136.992196] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [136.992390] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [136.998117] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [137.004203] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [137.009145] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [137.107957] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [137.108734] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [137.115895] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [137.117452] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [137.118238] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [137.119030] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [137.119600] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [137.120244] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [137.208020] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [137.208422] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [137.209127] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [137.209811] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [137.210610] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.211378] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.212114] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.212821] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.213546] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [137.214292] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [137.214927] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [137.215696] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [137.217942] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [137.218562] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [137.227703] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [137.228019] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [137.228393] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [137.233012] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [137.237900] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [137.242786] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [137.339084] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [137.339914] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [137.345862] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [137.347386] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [137.348203] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [137.349067] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [137.349690] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [137.350395] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [137.442083] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [137.442533] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [137.443326] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [137.444054] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [137.444874] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.445679] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.446520] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.447287] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.447592] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [137.447837] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [137.447986] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [137.448233] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [137.448922] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [137.449060] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [137.455233] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [137.455366] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [137.455524] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [137.460173] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [137.465041] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [137.469945] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [137.571080] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [137.571904] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [137.577812] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [137.579193] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [137.579433] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [137.579717] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [137.579869] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [137.580041] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [137.669070] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [137.669471] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [137.670193] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [137.670899] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [137.671640] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.672485] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.673263] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.673990] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.674669] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [137.675420] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [137.675938] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [137.676228] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [137.677064] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [137.677214] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [137.689493] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [137.689605] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [137.689744] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [137.694407] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [137.699315] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [137.704154] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [137.795135] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [137.795995] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [137.803061] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [137.804581] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [137.805382] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [137.806234] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [137.806875] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [137.807542] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [137.903102] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [137.903515] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [137.904311] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [137.905150] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [137.905972] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.906780] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.907646] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.908478] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [137.909254] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [137.909993] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [137.910607] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [137.911423] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [137.913682] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [137.914331] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [137.924667] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [137.924917] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [137.925233] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [137.931074] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [137.937181] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [137.942110] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [138.043137] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [138.044028] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [138.048779] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [138.050152] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [138.050386] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [138.050670] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [138.050811] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [138.050994] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [138.141075] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [138.141476] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [138.142200] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [138.142994] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [138.144060] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.144859] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.145689] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.146447] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.146654] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [138.146905] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [138.147094] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [138.147341] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [138.148040] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [138.148175] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [138.158064] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [138.158307] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [138.158568] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [138.163150] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [138.169212] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [138.175278] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [138.275111] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [138.275958] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [138.284557] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [138.286537] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [138.287671] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [138.288927] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [138.289800] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [138.292088] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [138.376105] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [138.376508] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [138.377228] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [138.377939] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [138.378942] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.379716] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.380549] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.381300] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.382024] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [138.382772] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [138.383450] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [138.384263] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [138.386484] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [138.387182] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [138.398762] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [138.398928] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [138.399149] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [138.403747] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [138.408602] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [138.413465] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [138.515123] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [138.516031] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [138.524652] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [138.526684] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [138.527789] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [138.528715] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [138.529732] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [138.530808] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [138.615994] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [138.616390] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [138.617091] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [138.617776] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [138.618551] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.619317] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.620047] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.620757] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.621482] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [138.623323] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [138.623997] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [138.624801] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [138.627049] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [138.627681] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [138.637998] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [138.638223] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [138.638518] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [138.644274] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [138.650325] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [138.656437] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [138.747114] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [138.749144] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [138.756503] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [138.757909] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [138.758175] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [138.758457] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [138.758596] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [138.758766] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [138.853134] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [138.853537] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [138.854255] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [138.854980] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [138.855776] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.856640] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.857476] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.858218] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [138.858632] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [138.858895] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [138.859064] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [138.859362] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [138.860104] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [138.860241] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [138.870093] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [138.870275] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [138.870519] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [138.875118] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [138.881125] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [138.887250] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [138.979138] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [138.979984] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [138.987334] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [138.988865] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [138.989717] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [138.990605] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [138.991560] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [138.992324] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [139.085125] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [139.085525] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [139.086258] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [139.087260] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [139.088096] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.088929] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.089710] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.090501] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.091247] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [139.092007] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [139.092619] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [139.093492] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [139.096135] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [139.096756] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [139.108312] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [139.108513] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [139.108780] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [139.114582] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [139.119500] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [139.124403] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [139.219147] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [139.219980] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [139.227342] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [139.229185] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [139.230003] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [139.230816] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [139.231503] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [139.232218] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [139.322077] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [139.322475] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [139.323218] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [139.323944] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [139.324950] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.325745] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.326512] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.327274] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.327897] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [139.328140] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [139.328277] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [139.328524] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [139.329212] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [139.329359] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [139.336803] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [139.336947] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [139.337099] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [139.342871] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [139.348985] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [139.353904] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [139.451143] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [139.451993] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [139.459347] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [139.461182] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [139.462004] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [139.462811] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [139.463499] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [139.464216] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [139.555115] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [139.555517] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [139.556242] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [139.557021] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [139.557767] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.558650] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.559480] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.560273] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.560995] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [139.561737] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [139.562063] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [139.562321] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [139.563006] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [139.563144] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [139.572991] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [139.573176] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [139.573430] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [139.579194] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [139.585295] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [139.590238] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [139.683208] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [139.684079] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [139.689990] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [139.691358] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [139.691590] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [139.691891] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [139.692061] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [139.692250] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [139.787122] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [139.787526] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [139.788253] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [139.789037] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [139.789837] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.790735] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.791563] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.792332] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [139.793045] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [139.793762] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [139.794444] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [139.795290] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [139.797526] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [139.798182] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [139.808506] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [139.808719] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [139.809056] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [139.813733] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [139.818607] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [139.824649] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [139.923150] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [139.923999] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [139.928726] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [139.930082] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [139.930321] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [139.930605] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [139.930746] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [139.930925] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [140.022122] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [140.022522] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [140.023230] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [140.023940] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [140.024833] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.025706] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.026522] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.027276] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.027988] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [140.028701] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [140.029360] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [140.030147] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [140.032359] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [140.032999] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [140.043334] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [140.043520] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [140.043785] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [140.048422] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [140.053312] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [140.058174] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [140.155188] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [140.156053] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [140.163117] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [140.164638] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [140.165439] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [140.166290] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [140.166933] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [140.167602] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [140.257522] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [140.257969] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [140.258652] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [140.259383] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [140.260170] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.260904] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.261676] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.262472] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.263272] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [140.263516] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [140.263653] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [140.263901] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [140.264628] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [140.264766] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [140.273364] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [140.273478] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [140.273624] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [140.278296] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [140.283209] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [140.288094] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [140.387149] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [140.388000] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [140.393935] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [140.395465] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [140.396264] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [140.397102] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [140.397725] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [140.398419] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [140.487167] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [140.487567] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [140.488294] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [140.489005] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [140.489730] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.490764] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.491750] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.492590] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.493041] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [140.493296] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [140.493429] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [140.493674] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [140.494394] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [140.494535] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [140.503205] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [140.503313] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [140.503655] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [140.509339] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [140.514269] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [140.520297] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [140.612166] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [140.612992] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [140.618904] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [140.620507] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [140.621305] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [140.622140] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [140.622762] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [140.623472] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [140.716054] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [140.716455] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [140.717180] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [140.717966] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [140.718812] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.719966] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.720746] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.721637] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.722432] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [140.723271] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [140.723981] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [140.724805] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [140.727064] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [140.727680] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [140.738170] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [140.738348] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [140.738875] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [140.743479] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [140.749542] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [140.754467] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [140.851216] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [140.852824] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [140.858879] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [140.860516] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [140.861356] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [140.862197] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [140.862821] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [140.863614] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [140.951146] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [140.951546] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [140.952264] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [140.952973] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [140.953724] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.954891] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.955739] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.956568] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [140.957382] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [140.958273] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [140.958923] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [140.959750] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [140.962024] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [140.962661] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [140.974364] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [140.974624] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [140.974894] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [140.979538] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [140.985578] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [140.991665] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [141.091168] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [141.092011] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [141.097916] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [141.099287] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [141.099532] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [141.099827] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [141.099988] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [141.100249] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [141.190149] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [141.190547] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [141.191262] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [141.192009] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [141.192829] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [141.194001] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [141.194709] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [141.195496] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [141.196232] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [141.196954] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [141.197139] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [141.197385] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [141.198101] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [141.198235] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [141.208044] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [141.208224] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [141.208412] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [141.214167] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [141.220288] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [141.225182] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [141.323169] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [141.323987] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [141.329903] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [141.331488] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [141.332288] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [141.333121] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [141.333740] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [141.334437] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [141.423155] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [141.423593] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [141.424329] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [141.425068] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [141.425890] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [141.427078] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [141.427856] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [141.428748] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [141.429565] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [141.430400] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [141.431083] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [141.431855] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [141.434198] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [141.434816] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [141.446370] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [141.446613] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [141.446864] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1]
<7> [141.451578] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-2]
<7> [141.457618] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:162:DP-1]
<7> [141.462542] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:169:HDMI-A-3]
<7> [141.555204] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [141.556046] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [141.561930] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [141.563336] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [141.563585] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [141.563879] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [141.564082] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [141.564256] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [141.650402] [IGT] i915_pm_rpm: finished subtest system-suspend-execbuf, SUCCESS
<7> [141.653713] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [141.653885] [IGT] i915_pm_rpm: exiting, ret=0
|